Manuals / CH Tech / Computer Equipment / Network Router

CH Tech EM405D user manual Figure A-1. 9-Pin DSUB Connector, TRIGGER IN 6 GND 7 GND 8 GND 9 GND

Models: EM405D

1 48

Download 48 pages 8.75 Kb

Page 35

Image 35

APPENDIX A - CONNECTORS

1 2 3 4 5

6 7 8 9

PIN DESCRIPTION

1+12V INPUT

2+12V INPUT

3+12V INPUT

4TRIGGER OUT

5TRIGGER IN

6GND

7GND

8GND

9GND

Figure A-1. 9-Pin DSUB Connector

A-1

Page 35

Image 35

CH Tech EM405D Figure A-1. 9-Pin DSUB Connector, PIN DESCRIPTION 1 +12V INPUT 2 +12V INPUT 3 +12V INPUT 4 TRIGGER OUT

Contents

Manual Part No U S E R S M A N U A L E T H E R N E T M - M O D U L E C A R R I E RM O D E L E M 4 0 5 D Copyright 2004 by C&H Technologies, Inc COPYRIGHTDOCUMENT REVISION NOTICE INTRODUCTION FUNCTIONAL DESCRIPTION TABLE OF CONTENTSINSTALLATION GENERAL DESCRIPTIONLIST OF FIGURES APPENDIX A - CONNECTORSAPPENDIX B - WIRED ETHERNET DEFAULT SETTINGS APPENDIX C - WIRELESS ETHERNET WI-FI DEFAULT SETTINGSFigure 1. EM405D Ethernet M-Module Carrier 1.1 PURPOSE OF EQUIPMENT 1.2 FEATURES AND SPECIFICATIONS 1.2.1 Key Features1.0 GENERAL DESCRIPTION Parameter 1.2.2 SpecificationsCHARACTERISTICS MAXIMUM RATINGS1.6 Bus Compliance 1.3 Electrical1.4 Mechanical 1.5 EnvironmentalIEEE-802.3 ANSI 8802.3, Ethernet Network Standard 1.7 APPLICABLE DOCUMENTSIEEE-802.11b, Wireless Ethernet Standard Figure 2. M-module Installation 2.0 INSTALLATION 2.1 UNPACKING AND INSPECTION2.2 HANDLING PRECAUTIONS 2.3 INSTALLATION OF M-MODULESMODULE A Figure 3. M/MA Configuration DiagramMODULE B ETHERNET Figure 4. Functional Block Diagram 3.1.1 Embedded Controller3.0 FUNCTIONAL DESCRIPTION 3.1 GENERAL 3.1.2 Ethernet InterfaceFigure 5. Rear Panel 3.1.4 Power Conversion3.1.3 M-module Interface 3.2 REAR PANELEM405D ETHERNET M-MODULE CARRIER 3.3 FRONT PANELFigure 6. Front Panel Page 4.2.1 IP Address 4.2 CONFIGURING THE ETHERNET INTERFACE4.0 OPERATING INSTRUCTIONS 4.1 GENERAL 4.2.5 Wireless Settings The default subnet mask is 4.2.3 GatewayThe default gateway address is 4.2.4 Port Numbers The default port number for standard module access is4.2.6 Performing the Configuration - Wired Ethernet The default setting is Auto-ScanThe default settings are WEP disabled and WPA disabled telnet x.x.x.x 4.2.7 Performing the Configuration - Wireless Ethernet Wi-Fi 4.2.7.1 Wed-based Configuration Table II. Status Code SC Table I. Command Summary4.3.1 Error Handling 4.3 COMMUNICATING WITH THE CARRIER AND M-MODULESSuccessful 0x00 The command completed successfully without error 4.3.3 Read Data command 4.3.2 Write Data command4.3.4 Block Access 4.3.4.1 Block Write command 4.3.4.2 Block Read command Register 4.3.5 EM405D Configuration/Status RegistersTable III. Register Summary OffsetFirmware Version Reset Error & Manufacturer IdentificationDevice Identification Hardware Version Module A Trigger B Direction 0 = input, 1 = output Reset & Trigger ControlFan Control & Temperature Status Figure 7. EM405D Registers continued4.4 CONTROLLING THE TRIGGERS C = TEMP - 281 4.5 FAN AND TEMPERATURE CONTROLPage 5 TRIGGER IN 6 GND 7 GND 8 GND 9 GND Figure A-1. 9-Pin DSUB ConnectorPIN DESCRIPTION 1 +12V INPUT 2 +12V INPUT 3 +12V INPUT 4 TRIGGER OUT Page Table B-1. Ethernet Interface Default Settings Table B-1. Ethernet Interface Default Settings. continued blank Table B-1. Ethernet Interface Default Settings. continuedOEM Configurable Pins Email NotificationPage Wireless Security Settings Table C-1. Wireless Ethernet Configuration Default SettingsIP Settings Wireless LAN SettingsTCP Client Settings Advanced Network SettingsPort Profile Settings TCP Server Settingsblank blankblank Page N O T E S Page READERS COMMENT FORM INSTRUCTIONS