Manuals
/
CH Tech
/
Computer Equipment
/
Network Router
CH Tech
EM405D user manual
Models:
EM405D
1
46
48
48
Download
48 pages
8.75 Kb
41
42
43
44
45
46
47
48
<
>
Specs
Characteristics
Install
M/MA Configuration Diagram
Configuring The Ethernet Interface
Appendix B - Wired Ethernet Default Settings
Reset Error & Manufacturer Identification
Table I. Command Summary
The default subnet mask is 4.2.3 Gateway
IP Settings
Page 46
Image 46
.
Page 45
Page 47
Page 46
Image 46
Page 45
Page 47
Contents
M O D E L E M 4 0 5 D
U S E R S M A N U A L E T H E R N E T M - M O D U L E C A R R I E R
Manual Part No
COPYRIGHT
Copyright 2004 by C&H Technologies, Inc
DOCUMENT REVISION NOTICE
INTRODUCTION
GENERAL DESCRIPTION
TABLE OF CONTENTS
INSTALLATION
FUNCTIONAL DESCRIPTION
APPENDIX C - WIRELESS ETHERNET WI-FI DEFAULT SETTINGS
APPENDIX A - CONNECTORS
APPENDIX B - WIRED ETHERNET DEFAULT SETTINGS
LIST OF FIGURES
1.0 GENERAL DESCRIPTION
1.2 FEATURES AND SPECIFICATIONS 1.2.1 Key Features
Figure 1. EM405D Ethernet M-Module Carrier 1.1 PURPOSE OF EQUIPMENT
MAXIMUM RATINGS
1.2.2 Specifications
CHARACTERISTICS
Parameter
1.5 Environmental
1.3 Electrical
1.4 Mechanical
1.6 Bus Compliance
IEEE-802.11b, Wireless Ethernet Standard
1.7 APPLICABLE DOCUMENTS
IEEE-802.3 ANSI 8802.3, Ethernet Network Standard
2.3 INSTALLATION OF M-MODULES
2.0 INSTALLATION 2.1 UNPACKING AND INSPECTION
2.2 HANDLING PRECAUTIONS
Figure 2. M-module Installation
MODULE B
Figure 3. M/MA Configuration Diagram
MODULE A
3.1.2 Ethernet Interface
Figure 4. Functional Block Diagram 3.1.1 Embedded Controller
3.0 FUNCTIONAL DESCRIPTION 3.1 GENERAL
ETHERNET
3.2 REAR PANEL
3.1.4 Power Conversion
3.1.3 M-module Interface
Figure 5. Rear Panel
Figure 6. Front Panel
3.3 FRONT PANEL
EM405D ETHERNET M-MODULE CARRIER
Page
4.0 OPERATING INSTRUCTIONS 4.1 GENERAL
4.2 CONFIGURING THE ETHERNET INTERFACE
4.2.1 IP Address
The default port number for standard module access is
The default subnet mask is 4.2.3 Gateway
The default gateway address is 4.2.4 Port Numbers
4.2.5 Wireless Settings
The default settings are WEP disabled and WPA disabled
The default setting is Auto-Scan
4.2.6 Performing the Configuration - Wired Ethernet
telnet x.x.x.x
4.2.7 Performing the Configuration - Wireless Ethernet Wi-Fi
4.2.7.1 Wed-based Configuration
4.3 COMMUNICATING WITH THE CARRIER AND M-MODULES
Table I. Command Summary
4.3.1 Error Handling
Table II. Status Code SC
Successful 0x00 The command completed successfully without error
4.3.2 Write Data command
4.3.3 Read Data command
4.3.4 Block Access
4.3.4.1 Block Write command
4.3.4.2 Block Read command
Offset
4.3.5 EM405D Configuration/Status Registers
Table III. Register Summary
Register
Hardware Version
Reset Error & Manufacturer Identification
Device Identification
Firmware Version
Figure 7. EM405D Registers continued
Reset & Trigger Control
Fan Control & Temperature Status
Enclosure Temperature C = TEMP - 281
4.4 CONTROLLING THE TRIGGERS
4.5 FAN AND TEMPERATURE CONTROL
C = TEMP - 281
Page
PIN DESCRIPTION 1 +12V INPUT 2 +12V INPUT 3 +12V INPUT 4 TRIGGER OUT
Figure A-1. 9-Pin DSUB Connector
5 TRIGGER IN 6 GND 7 GND 8 GND 9 GND
Page
Table B-1. Ethernet Interface Default Settings
Table B-1. Ethernet Interface Default Settings. continued
Email Notification
Table B-1. Ethernet Interface Default Settings. continued
OEM Configurable Pins
blank
Page
Wireless LAN Settings
Table C-1. Wireless Ethernet Configuration Default Settings
IP Settings
Wireless Security Settings
TCP Server Settings
Advanced Network Settings
Port Profile Settings
TCP Client Settings
blank
blank
blank
Page
N O T E S
Page
READERS COMMENT FORM
INSTRUCTIONS
