Chamberlain HD920EV, WD962KEV, WD962KPEV 39

Remote Control

Your garage door opener has been programmed at the factory to operate with your remote control. The remote control can be programmed using the door control or the garage door opener. To program additional remote controls refer to the instructions provided with the additional remote controls or visit www.chamberlain.com.

TO ADD, REPROGRAM, OR CHANGE A REMOTE CONTROL/KEYLESS ENTRY PIN USING THE MOTION-DETECTING CONTROL PANEL

1Press the LEARN button on the door control to enter Programming Mode.

The command LED will ﬂash once.

2Press the LEARN button again, the LED will ﬂash once.

The command LED will ﬂash once again.

3a Press the button on the remote control that you wish to operate your garage door.

3b Enter a 4-digit personal

identiﬁcation number (PIN) of

your choice on the keyless entry

OR

keypad. Then press the ENTER

button.

1

2

3

4

5

6

#

0 QZ

?

?

?

?

7

8

9

*

0

#

ENTER

ENTER

PIN

The garage door opener lights will ﬂash (or two clicks will be heard) when the code has been programmed.

Repeat the steps above for programming additional remote controls or keyless entry devices.

TO ADD, REPROGRAM, OR CHANGE A REMOTE CONTROL/KEYLESS ENTRY PIN USING THE SMART CONTROL PANEL

1 Press the navigation	2 Use the navigation buttons
button below "MENU"	to scroll to "PROGRAM" and
to view the Features	press the navigation button
menu.	under				to continue.

3Select "REMOTE" or "KEYPAD" to program from the program menu. Press to continue.

O REMO E

4a Press the button on the remote		4b Enter a 4-digit personal
control that you wish to operate		identiﬁcation number (PIN) of
your garage door.		your choice on the keyless entry
OR		keypad. Then press the ENTER
OR		button.
			1
			1	2	3
					6
				5	6
					9	0 QZ	#
				8	9	0 QZ	#
						#
				0		#
?	?	?	?	NTER
?	?	?	?			ENTER

PIN

39

Contents

■Please read this manual and the enclosed safety materials carefully ■Fasten the manual near the garage door after installation Preparation Assembly Installation Mechanical Electrical Additional items you may need for installation: A. (2) 2X4 PIECES OF WOOD C. EXTENSION BRACKETS (MODEL GARAGE DOOR OPENER ASSEMBLY The Protector System® INSTALLATION HARDWARE DOOR CONTROL HARDWARE Page HARDWARE Page HARDWARE H9 (3) Page Page Option B CEILING INSTALLATION Page H10 (2) H20 (2) H21 (2) H15 (2) Tip: HARDWAREH16 (2) Option B ONE-PIECEDOORS 8.1B 8.2B Metal Doors: Wood Doors: IMPORTANT: ONE-PIECEDOORS 9.1A 9.2A 9.3A Option B SECTIONAL DOORS 9.1B 9.2B 9.3B 9.4B INTRODUCTION PRE-WIREDINSTALLATIONS: When wiring IMPORTANT INFORMATION ABOUT THE SAFETY REVERSING SENSOR H17 (2) H18 (2) Option A DOOR TRACK INSTALLATION 1.1A 1.2A Option C FLOOR INSTALLATION 1.1C 1.2C 1.3C 1.4C Option B PRE-WIREDINSTALLATION 2.1B 2.4B 2.5B THERE ARE TWO OPTIONS FOR CONNECTING POWER: Option A TYPICAL WIRING 1.1A Option B PERMANENT WIRING 1.1B IF THE AMBER LED ON THE SENDING SENSOR IS NOT GLOWING: Tip: ONE-PIECEDOORS ONLY PROGRAMMING BUTTONS Page Page Test the battery BATTERY STATUS LED GREEN LED: ORANGE LED: RED LED: CHARGE THE BATTERY Page TIMER-TO-CLOSE MYQ™ SECURITY✚ 2.0™ REMOTE CONTROLS AND DOOR CONTROLS THE PROTECTOR SYSTEM® (SAFETY REVERSING SENSORS) ENERGY CONSERVATION SYNCHRONIZE THE DOOR CONTROL LEARN A DEVICE TIMER-TO-CLOSE(TTC) PUSH BAR LIGHT BUTTON TIMER-TO-CLOSE(TTC) LOCK LIGHT MOTION SENSOR MENU NAVIGATION SCREEN FEATURES SETTINGS LOCK Page PROGRAM A REMOTE USING THE LEARN BUTTON ERASE ALL REMOTE CONTROLS AND KEYLESS ENTRIES ERASE ALL DEVICES DISCONNECT THE TROLLEY RECONNECT THE TROLLEY EVERY MONTH EVERY YEAR EVERY TWO TO THREE YEARS DIAGNOSTIC UP ARROW DOWN SYMPTOM CAUSE 4 FLASHES 2 FLASHES 5 FLASHES 6 FLASHES My garage door opener beeps every 30 seconds: Installation Parts DESCRIPTION NOT SHOWN PART NUMBER Page CHAMBERLAIN® FIVE YEAR LIMITED WARRANTY LIFETIME MOTOR AND BELT LIMITED WARRANTY ONE YEAR LIMITED WARRANTY FOR THE BATTERY BACKUP 7702CB Outside Quick Release: 41A5281 Extension Brackets: System Surge Protector: