Cino FM400 - page 13

FuzzyScan Fixed Mount

Scan

Programming Manual

9

Scan

“END”

FuzzyScan will exit programming mode, and store all

parameters in Flash Memory ASIC or non-volatile memory,

then issue the completion beeping.

Scan

“PROGRAM”

FuzzyScan will enter programming mode,

and inhibit all non-programming functions.

Scan

“SYSLIST”

FuzzyScan will list the product information and

revision number to host via selected host interface,

then issue the completion beeping.

Scan

“

M_DEFAULT

”

FuzzyScan will recover all programmable

parameters into factory preset configurations,

then issue the completion beeping.

Program & End

Program & EndProgram & End

Program & End

Please note that the FuzzyScan will take 3-4 seconds to

store parameters in internal Flash Memory ASIC or

non-volatile memory after you scan the “END”. Please

don’t turn off the power before the completion beeping. It

may destroy all configured parameters.

System List, Group & Master Default

System List, Group & Master DefaultSystem List, Group & Master Default

System List, Group & Master Default

Contents

Main Revision History Warranty Regulatory Table of Contents Getting Started Configure Your FuzzyScan Appendix Getting Familiar with Your FuzzyScan FM400 Series (Front-view Model) FM400 Series (Side-view Model) Connect to Your Host USB Models (FM4xx-11x) RS232 Models (FM4xx-00x) Universal Models (FM4xx-98x) Install Your FuzzyScan Adjust Reading Angle Mount Your FuzzyScan Use the Test Mode Test Button Test Mode Use Your FuzzScan External Trigger and Serial Trigger Scan Input Time-out OK/NG Signals Operation Modes Page Bar Code Programming Menu Page Page Single scan selection Single scan selectionSingle scan selection Single scan selection Yes No No Cycling scan selection Cycling scan selectionCycling scan selection Cycling scan selection No Yes Yes Host Interface Selection PROGRAM User Defined Symbol ID F_DEFAULT Symbology ID Transmission PROGRAM Readable Bar Code Setting F_DEFAULT Page Page PROGRAM Codabar/NW-7 Setting F_DEFAULT UPC-A & UPC-E Setting F_DEFAULT UPC-A & UPC-E Setting , Supplement Scan Voting F_DEFAULT EAN Setting , Supplement , Supplement Scan Voting F_DEFAULT UPC/EAN Security Level Setting , EAN Supplement Control F_DEFAULT Page PROGRAM IATA & Interleaved 2 of 5 Setting F_DEFAULT Code 25 Family Setting Code 11 & Code 93 Setting MSI/Plessey Setting Code 128 & UCC/EAN 128 Setting UK/Plessey Setting Telepen Setting PROGRAM GS1 DataBar Setting F_DEFAULT Linear-stacked & Korea Post Code Setting PROGRAM Keyboard Layout (Language) Setting F_DEFAULT Record Suffix, Preamble, Postamble & Caps Lock Delay Setting Emulation Setting & Upper/Lower Case Setting PROGRAM Record Suffix, Preamble, Postamble Setting F_DEFAULT Delay Setting Protocol, ACK/NAK Setting PROGRAM Time Out Setting, Baud Rate, Data Frame F_DEFAULT Operation Mode Setting F_DEFAULT Buzzer, Indicator, Inverse Reading PROGRAM Dollar Sign, Redundancy, Scan Rate Control F_DEFAULT Delay Setting F_DEFAULT Parameter Selection Option Code Reread Delay (Double San Verification) Good Read Delay Time-out and Duration Setting F_DEFAULT Presentation Scanning Setting PROGRAM OK/NG Signal and Beeping Control F_DEFAULT Page PROGRAM Preamble, Postamble, Data Length & Symbol ID Trans. F_DEFAULT Data Formatter Setting F_DEFAULT Data Verifier Setting F_DEFAULT Data Replacer Setting Data Organizer Setting Select a Bar Code Symbology Select a Bar Code SymbologySelect a Bar Code Symbology Select a Bar Code Symbology Position Calculation Position CalculationPosition Calculation Application Example Application ExampleApplication Example Application Example Programming Procedure Programming ProcedureProgramming Procedure Programming Procedure [Data Verifier] [Data Formatter] [Data Replacer] Symbology ID Table Keyboard Function Code Table ASCII Input Shortcut Example: HEX/ASCII Reference Table Host Interface Quick Set Operation Mode Quick Set Option Codes System Commands Indications Normal Operation Test Mode Reading Rate Information