Cisco Systems 1240AG - page 18

1-4

Cisco Aironet 1240AG Series Access Point Hardware Installation Guide

OL-8371-05

Chapter1 Overview

Hardware Features

Figure 1-2 illustrates the 2.4-GHz connector end of the access point.

Figure1-2 Access Point 2.4 GHz Connector End

Figure 1-3 illustrates the 5-GHz connector end of the access point.

Figure1-3 Access Point 5-GHz Connector End

12.4-GHz antenna connector (left) 6Console port (RJ-45)

2Ethernet LED 7Ethernet port (RJ-45)

3Radio LED 848-VDC power port

4Status LED 92.4-GHz antenna connector (right/primary)

5Mode button

STATUS

RADIO

ETHERNET

MODE

CONSOLE ETHERNET 48VDC

2.4 GHz RIGHT/PRIMARY

2.4 GHz LEFT

135435

6 7 8 91 5432

15-GHz antenna connector (left) 3Security key slot

25-GHz antenna connector (right/primary)

LEFT

5 GHz ANTENNA w/RP-TNC

135436

1

RIGHT / PRIMARY

23

Contents

Main Page CONTENTS Page Page Page Page Page Preface Audience Purpose Organization Conventions xi or loss of data. Related Publications Locating the Product Serial Number CAUTION Hot Surfaces Page Overview Product Terminology Autonomous Access Points Lightweight Access Points Guidelines for Using Cisco Aironet Lightweight Access Points Hardware Features Page Single or Dual-Radio Operation Antennas Supported Ethernet Port Console Port LEDs Power Sources UL 2043 Certification Anti-Theft Features Page Network Examples with Autonomous Access Points Root Access Point on a Wired LAN Repeater Unit that Extends Wireless Range Central Unit in an All-Wireless Network Bridge Network with Wireless Clients Point-to-Point Bridge Configuration Workgroup Bridge Network Network Example with Lightweight Access Points Page Installing the Access Point Safety Information FCC Safety Compliance Statement General Safety Guidelines Warnings Unpacking the Access Point Package Contents Basic Installation Guidelines Controller Discovery Process for Lightweight Access Points Deploying the Access Points on the Wireless Network Access Point Layout and Connectors Mounting Overview Page Mounting on a Horizontal or Vertical Surface Mounting Below a Suspended Ceiling Mounting Above a Suspended Ceiling Page Page Mounting Access Point on a Desktop or Shelf Cable Security Bracket Removing the Cable Security Bracket Attaching the Access Point to the Mounting Plate Securing the Access Point Using a Security Cable Securing the Access Point to the Mounting Plate Page 2-20 Cisco Aironet 1240AG Series Access Point Hardware Installation Guide OL-8371-05 Access Point Chapter2 Installing the Access Point Connecting the Ethernet and Power Cables Connecting the Ethernet and Power Cables Figure2-12 Access Point Power Options Statement 353 Option 1Switches with sufficient inline power: Other inline power switches supporting the IEEE 802.3af inline power standard Connecting to an Ethernet Network with an Inline Power Source Connecting to an Ethernet Network with Local Power Powering Up the Access Point Troubleshooting 1240AG Series Autonomous Checking the Autonomous Access Point LEDs Checking Basic Settings Default IP Address Behavior Enabling the Radio Interfaces SSID WEP Keys Security Settings Low Power Condition Intelligent Power Management Inline Power Status Messages Page Configuring Power Using the CLI Issuing the Cisco IOS Command Using the CLI Configuring the Access Point System Power Settings Using a Browser Page Running the Carrier Busy Test Running the Ping Test Resetting to the Default Configuration Using the MODE Button Using the Web Browser Interface Reloading the Access Point Image Using the MODE Button Web Browser Interface Browser HTTP Interface Browser TFTP Interface Obtaining the Access Point Image File Connecting to the Access Point Locally Obtaining the TFTP Server Software Troubleshooting 1240AG Series Lightweight Guidelines for Using Cisco Aironet Lightweight Access Points Using DHCP Option 43 Checking the Lightweight Access Point LEDs Page Low Power Condition for Lightweight Access Points Intelligent Power Management Configuring Power Using Controller CLI Commands Manually Configuring Controller Information Using the Access Point CLI Configuring Controller Information Clearing Manually Entered Controller Information Manually Resetting the Access Point to Defaults Returning the Lightweight Access Point to Autonomous Mode Using a Controller to Return the Access Point to Autonomous Mode Using the MODE Button to Return the Access Point to Autonomous Mode MODE Button Setting Obtaining the Autonomous Access Point Image File Connecting to the Access Point Locally Obtaining the TFTP Server Software A Translated Safety Warnings Page B Declarations of Conformity and Regulatory Information Manufacturers Federal Communication Commission Declaration of Conformity Statement Tested To Comply With FCC Standards FOR HOME OR OFFICE USE VCCI Statement for Japan Industry Canada Canadian Compliance Statement European Community, Switzerland, Norway, Iceland, and Liechtenstein Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive) Page Page Declaration of Conformity for RF Exposure Guidelines for Operating Cisco Aironet Access Points in Japan Japanese Translation 03-6434-6500 Administrative Rules for Cisco Aironet Access Points in Taiwan Access Points with IEEE 802.11a Radios All Access Points Chinese Translation Operation of Cisco Aironet Access Points in Brazil Access Point Models Regulatory Information Portuguese Translation Page DECLARATION OF CONFORMITY with regard to the R&TTE Directive 1999/5/EC Signature: Tony Youssef Director Corporate Compliance Annex to DofC# 456136rev1 Information on Antennas and Power Levels C Access Point Specifications Page Page Page D Channels and Maximum Power Levels Page E Console Cable Pinouts Overview Console Port Signals and Pinouts F Priming Lightweight Access Points Prior to Deployment Page Page Page G Configuring DHCP Option 43 for Lightweight Overview Configuring Option 43 for 1000 Series Access Points Configuring Option 43 for 1100, 1130, 1200, 1240, and 1300 Series Lightweight Access Points GLOSSARY A B C D E F G I L M O P Q R Page U W Page INDEX A B C P R S T