Manuals / Cisco Systems / Computer Equipment / Network Router

Cisco Systems 1300 Series manual Blinking Codes, First, Second, Digit, Description

Models: 1300 Series

1 146

Download 146 pages 10.97 Kb

Page 84

Image 84

Chapter 7 Troubleshooting

Checking the LEDs

The LED blinking error codes are described in Table 7-2.

Table 7-2	LED Blinking Error Codes

	Blinking Codes

	First	Second
LED	Digit	Digit	Description

Ethernet	2	1	Ethernet cable problem—verify that the cable is properly connected
			and not defective. This error might also indicate a problem with the
			Ethernet link. If the cable is connected properly and not defective,
			contact technical support for assistance.

Radio	1	2	Radio not detected—contact technical support for assistance.

	1	3	Radio not ready—contact technical support for assistance.

	1	4	Radio did not start—contact technical support for assistance.

	1	5	Radio failure—contact technical support for assistance.

	1	6	Radio did not flash its firmware—contact technical support for
			assistance.

Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide

7-4	OL-5048-02

Page 84

Image 84

Cisco Systems 1300 Series manual Blinking Codes, First, Second, Digit, Description, LED Blinking Error Codes

Contents

April Cisco Systems, Inc 170 West Tasman Drive San Jose, CA800 553-NETS Fax 408 Access Point/Bridge Hardware Installation GuideTurn the television or radio antenna until the interference stops Power Port Aggregation or Redundancy Bridge ConfigurationDefinitions of Service Request Severity Key FeaturesAll Installations Unpacking the Access Point/BridgeSafety Warnings Access Point ConfigurationUsing VLANs Adjusting Output Power LevelIOS Command Modes Recalling CommandsSecurity Settings TroubleshootingPower Injector Default IP Address BehaviorSignals and Pinouts E-2 Statement 1030-Equipment InstallationChannels OverviewLoad-Dump Protection F-1 viiiContents OL-5048-02Preface ObjectivesAudience OrganizationConventions Attention Ce symbole d’avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures. Avant d’accéder à cet équipement, soyez conscient des dangers posés par les circuits électriques et familiarisez-vous avec les procédures courantes de prévention des accidents. Pour obtenir les traductions des mises en garde figurant dans cette publication, veuillez consulter l’annexe intitulée « Translated Safety Warnings » Traduction des avis de sécurité Related Publications Obtaining DocumentationCisco.com Documentation Feedback Documentation DVDOrdering Documentation xiiiReporting Security Problems in Cisco Products Cisco Product Security OverviewObtaining Technical Assistance Emergencies - security-alert@cisco.comCisco Technical Support Website Locating the Product Serial Numberhttp//tools.cisco.com/RPF/register/register.do Submitting a Service Request Definitions of Service Request Severity Obtaining Additional Publications and Informationxvii xviii Preface Obtaining Additional Publications and InformationOL-5048-02 Key Features, page Network Configuration Examples, page OverviewC H A P T E R Key Features Power Integrated AntennaConnectors External AntennaEthernet Ports EnclosureLEDs Operating Roles Network Configuration Examples Point-to-Point Bridge ConfigurationPort Aggregation or Redundancy Bridge Configuration Point-to-Multipoint Bridge Configuration Access Point ConfigurationFigure 1-6 Point-to-Multipoint Bridge Configuration Figure 1-7 Access Point ConfigurationWorkgroup Bridge Configuration Figure 1-8 Workgroup Bridge ConfigurationFigure 1-9 Workgroup Bridge Configuration 1-10 Chapter 1 Overview Network Configuration ExamplesOL-5048-02 Installation Overview Safety Warnings, page Safety Information, pageUnpacking the Access Point/Bridge, page Before Beginning the Installation, page Installation Summary, pageSafety Warnings All InstallationsSafety Information Outdoor and Vehicle InstallationsVehicle Bridge Installations FCC Safety Compliance StatementSafety Precautions Installation Guidelines Typical Outdoor Installation ComponentsUnpacking the Access Point/Bridge Package ContentsSite Surveys Before Beginning the Installation Figure 2-2 Access Point/Bridge Layout Power Injector Indicators and ConnectorsCISCOPOWER Installation Summary Power Module2-10 2-11 Seal all external connectors with special weather sealing material2-12 Chapter 2 Installation Overview Installation SummaryOL-5048-02 Mounting the Access Point/Bridge, page Mounting Hardware, page Aligning the Bridge Antenna Using RSSI LED Indications, pageMounting and Alignment Overview LEDs, pageMounting the Access Point/Bridge Mounting HardwareWindow Mounting Multi-Function MountAccess Point/Bridge Bracket Mast BracketMast Type Mast DiameterLEDs Bridge State Install LEDStatus Aligning the Bridge Antenna Using RSSI LED Indications RSSI Level dBmEthernet LED Status LEDAligning the Bridge Antenna Using RSSI LED Indications Chapter 3 Mounting and Alignment OverviewOL-5048-02 Using the Web-Browser Interface Using the Web-Browser Interface Management Pages, pageConnecting Locally to the Ethernet Port, page C H A P T E RUsing the Web-Browser Interface Management Pages Using Action Buttons Button or LinkDescription Using Online Help Password entry fieldsCharacter Restrictions in Entry Fields All other entry fieldsConnecting Locally to the Ethernet Port Chapter 4 Using the Web-Browser Interface Connecting Locally to the Ethernet PortOL-5048-02 Configuring the Access Point/Bridge for the First Time Resetting the Access Point/Bridge to Default Settings, pageDefault IP Address Behavior, page Default SSID and Default Role, page Connecting to the Access Point/Bridge Locally, pageResetting the Access Point/Bridge to Default Settings Default IP Address BehaviorStep 7 Click Reset to Defaults Before You StartDefault SSID and Default Role Obtaining and Assigning an IP AddressConnecting to the Access Point/Bridge Locally Using the Power Injector’s Ethernet PortUsing the Power Injector’s Console Port Assigning Basic Settings Figure 5-2 Express Setup Page IP Subnet Mask-Enter the IP subnet mask provided by your network administrator so that the IP address can be recognized on the LAN. If DHCP is enabled, leave this field blank Default Settings on the Express Setup Page Default SettingCisco IOS Release 12.32JA2 or ParameterAdjusting Output Power Level Configuring Basic Security SettingsPoint/Bridge Output Power” section on page D-4 Enabling the Radio Interfaces5-10 Chapter 5 Configuring the Access Point/Bridge for the First TimeConfiguring Basic Security Settings Figure 5-3 Express Security PageUnderstanding Express Security Settings Using VLANsCisco IOS Software Configuration Guide for Cisco Aironet Access PointsExpress Security Limitations 5-12Security Types on Express Security Setup Page continued Finding the IP Address Using the CLI Using the Express Security Page5-13 Assigning an IP Address Using the CLI Using a Telnet Session to Access the CLIconfigure terminal Step 1 Select Start Programs Accessories TelnetUsing the Command-Line Interface Connecting to the Console Serial Port, pageUsing a Telnet Session to Open the CLI, page IOS Command Modes, page Getting Help, page Abbreviating Commands, pageConnecting to the Console Serial Port Using a Telnet Session to Open the CLI Using Secure Shell to Open the CLIStep 1 Select Start Programs Accessories Telnet IOS Command Modes the configureEnter logout or quit Access MethodAbbreviating Commands Using no and default Forms of Commandsabbreviated-command-entry? abbreviated-command-entryTabUsing Command History Changing the Command History Buffer Size, pageRecalling Commands, page Disabling the Command History Feature, page Understanding CLI MessagesChanging the Command History Buffer Size Recalling CommandsDisabling the Command History Feature show historyUsing Editing Features Enabling and Disabling Editing FeaturesEditing Commands Through Keystrokes Enabling and Disabling Editing Features, pageEditing Command Lines That Wrap Delete or BackspaceCtrl-D Ctrl-KSearching and Filtering Output of show and more Commands command begin include exclude regular-expression6-10 Finding the Access Point/Bridge IP Address Using the CLI Step 1 show interface bvi1Display the IP address for the interface BVI 6-116-12 Chapter 6 Using the Command-Line InterfaceFinding the Access Point/Bridge IP Address Using the CLI OL-5048-02Troubleshooting Checking the LEDs, page Power Injector, page Checking Power, pageChecking Basic Configuration Settings, page Antenna Alignment, page Resetting the Access Point/Bridge to the Default Configuration, pageNormal Mode LED Indications Checking the LEDsInstall EthernetStatus RadioLED Blinking Error Codes Blinking CodesFirst SecondPower Injector Power InjectorChecking Power Checking Basic Configuration SettingsDefault IP Address Behavior Default SSID and Radio BehaviorEnabling the Radio Interface SSIDSecurity Settings Antenna AlignmentRunning the Carrier Busy Test Running the Ping or Link Test Using the Web-Browser Interface Using the CLI7-10 Resetting the Access Point/Bridge to the Default ConfigurationReloading the Access Point/Bridge Image Web-Browser InterfaceBrowser HTTP Interface 7-11Browser TFTP Interface 7-12Obtaining the Access Point/Bridge Image File Step 12 Click Option 2 Aironet Wireless Software Display TablesObtaining the TFTP Server Software http//tftpd32.jounin.net7-14 Chapter 7 Troubleshooting Reloading the Access Point/Bridge ImageOL-5048-02 Translated Safety Warnings Statement 1030-Equipment Installation, page A-10Statement 1033-SELV-IEC 60950 DC Power Supply, page A-12 Statement 1052-Installing and Grounding the Antenna, page A-15Statement 84-Warning Definition Statement 245B-Explosive Device Proximity Warning Statement 346-RF Exposure Limits Statement 1001-Work During Lightning Activity Statement 1005-Circuit Breaker Statement 1022-Disconnect Device Page Statement 1024-Ground Conductor Statement 1030-Equipment Installation A-10A-11 Statement 1033-SELV-IEC 60950 DC Power Supply A-12Statement 1040-Product Disposal A-13A-14 Statement 1052-Installing and Grounding the Antenna A-15A-16 A-17 Appendix A Translated Safety WarningsStatement 1052-Installing and Grounding the Antenna OL-5048-02A-18 Appendix A Translated Safety WarningsStatement 1052-Installing and Grounding the Antenna OL-5048-02Declarations of Conformity and Regulatory Information A P P E N D I X BDepartment of Communications-Canada, page B-3 Declaration of Conformity for RF Exposure, page B-5Models FCC Certification numberManufacturer Tested To Comply With FCC Standards FOR HOME OR OFFICE USEDepartment of Communications-Canada European Community, Switzerland, Norway, Iceland, and LiechtensteinCanadian Compliance Statement Page Declaration of Conformity for RF Exposure Japanese TranslationEnglish Translation 03-5549-6500All Access Points and Bridges Chinese Translation English TranslationDeclaration of Conformity Statements Declaration of Conformity Statements for European Union CountriesAppendix B Declarations of Conformity and Regulatory Information Access Point/Bridge Specifications A P P E N D I X CAccess Point/Bridge Power Injector and Power ModuleCategory Access Point/Bridge Power Injector and Power ModuleCategory Bridge Operating Range Bridge Antenna Configuration Data Rate MbpsAppendix C Access Point/Bridge Specifications OL-5048-02Channels and Antenna Settings Channels, page D-2 Maximum Power Levels and Antenna Gains, page D-3A P P E N D I X D OL-5048-02Channels IEEE 802.11g 2.4-GHz BandMaximum Power Levels and Antenna Gains IEEE 802.11g 2.4-GHz BandRegulatory Domain OFDMChanging the Access Point/Bridge Output Power Page Appendix D Channels and Antenna Settings Maximum Power Levels and Antenna GainsOL-5048-02 Overview, page E-2 Signals and Pinouts, page E-2 Console Serial Cable PinoutsA P P E N D I X E OL-5048-02Signals and Pinouts OverviewLoad-Dump Protection for Transportation Vehicles Load-Dump ProtectionA P P E N D I X F Page Numeric G L O S S A R YGL-1 A single data message packet sent to all addresses on the same subnet GL-2GL-3 The echoes created as a radio signal bounces off of physical objects A single data message packet sent to multiple addressesGL-4 GL-5 GL-6 GlossaryOL-5048-02 I N D E IN-1IN-2 IN-3 temperature, operating C-1 terminal emulator 5-4 troubleshootingunpacking user EXEC mode warnings 2-2, A-1 Web-based interface, common buttons 4-3 weight C-2IN-4 IndexOL-5048-02