Chapter 19 DLPs D200 to D299

DLP- D237 Roll Two Cross-Connects on One Optical Circuit Using Manual Routing

Step 13 Set the circuit path protection:

To route the circuit on a protected path, leave Fully Protected Path checked and continue with Step 14.

To create an unprotected circuit, uncheck Fully Protected Path and continue with Step 15.

Step 14 If you checked Fully Protected Path, choose one of the following:

Nodal Diversity Required—Ensures that the primary and alternate paths within the SNCP portions of the complete circuit path are nodally diverse.

Nodal Diversity Desired—Specifies that node diversity is preferred, but if node diversity is not possible, CTC creates fiber-diverse paths for the SNCP portion of the complete circuit path.

Link Diversity Only—Specifies that only fiber-diverse primary and alternate paths for SNCP portions of the complete circuit path are needed. The paths might be node-diverse, but CTC does not check for node diversity.

Step 15 Click Next. Beneath Route Review and Edit, node icons appear for you to route the circuit manually.

The green arrows pointing from the source node to other network nodes indicate spans that are available for routing the circuit.

Step 16 Complete the “DLP-D98 Provision a High-Order Circuit Route” task on page 17-96, or the “DLP-D3 Provision a Low-Order VC12 Circuit Route” task on page 17-2.

Caution The following is only seen with DUAL roll mode when both ends of the circuit use the card(s) mentioned in this statement. If the termination card is a DS3i-N-12, E1-N-14, E1-42 or E3-12 card, a roll will occur even if a valid signal is not detected on the Roll To port. The absence of a PDI-P downstream for LOS, LOF, and AIS line defects causes the roll to continue without a valid signal.

Step 17 Click Finish. In the Circuits tab, verify that a new circuit appears.

This circuit is the Roll To circuit. It is designated with the Roll From circuit name appended with ROLL**.

Step 18 Click the Rolls tab. Two new rolls now appear on the Rolls tab. For each pending roll, view the Roll Valid Signal status. When one of the following conditions is met, continue with Step 19.

If the Roll Valid Signal status is true, a valid signal was found on the new port.

If the Roll Valid Signal status is false, a valid signal was not found. Wait until the signal is found before continuing with the next step. If the signal is not found, refer to the Circuits and Timing section of the Cisco ONS 15454 SDH Troubleshooting Guide. To cancel the roll, see the “DLP-D240 Cancel a Roll” task on page 19-44.

The roll is a one-way destination roll and the Roll Valid signal status is false. It is not possible to get a Roll Valid Signal status of true for a one-way destination roll.

Note You cannot cancel an automatic roll after a valid signal is found.

A roll can be forced onto the Roll To Circuit destination without a valid signal by using the

Force Valid Signal button. If you choose Force Valid Signal, traffic on the circuit that is involved in the roll will be dropped when the roll is completed.

Step 19 If you selected Manual in Step 5, click each roll and click Complete to route the traffic to the new port. If you selected Auto, continue with Step 20.

 

 

Cisco ONS 15454 SDH Procedure Guide, R7.2

 

 

 

 

 

 

October 2007

 

 

19-41

 

 

 

 

 

Page 41
Image 41
Cisco Systems D200 manual 19-41

D200 specifications

Cisco Systems has long been a leader in networking technology, and one of its standout products is the Cisco D200. Designed to meet the demands of modern businesses, the D200 is a versatile and robust device that facilitates seamless connectivity and effective network management.

The Cisco D200 is primarily known for its performance and reliability in various deployment scenarios. It is equipped with dual-band Wi-Fi capabilities, supporting both 2.4 GHz and 5 GHz frequencies. This allows users to optimize their wireless network, reducing interference and providing the flexibility to support a wide range of devices in an increasingly wireless world.

One of the standout features of the D200 is its advanced security protocols. Featuring integrated firewalls and support for VPNs, the device ensures that data remains protected against potential cyber threats. With the rise in remote work and digital collaboration, the D200 provides businesses with secure access control, ensuring that sensitive information is safeguarded from unauthorized access.

Another key characteristic of the D200 is its ease of management. With Cisco's user-friendly interface, network administrators can easily configure and monitor the device. The D200 is also compatible with Cisco's DNA Center, enabling businesses to leverage automation and AI-driven insights to optimize their networks and improve operational efficiency.

Performance-wise, the D200 boasts impressive throughput capabilities, making it suitable for high-traffic environments such as offices and educational institutions. Its robust hardware allows for multiple concurrent connections, ensuring that even during peak usage times, network performance remains uninterrupted. Quality of Service (QoS) features also prioritize critical applications, enhancing the overall user experience.

In terms of scalability, the D200 is designed to grow with a business. Whether an organization is expanding its device fleet or increasing bandwidth demands, the D200 can adapt to these changes without compromising performance. Moreover, ongoing firmware updates from Cisco ensure that the device remains current with the latest technologies and security enhancements.

In summary, the Cisco D200 is an essential tool for any business seeking to enhance its networking capabilities. With its advanced features, secure architecture, and ease of management, it stands out as a reliable choice for organizations looking to future-proof their networking infrastructure. As technology continues to evolve, the D200 remains a stalwart in enabling connectivity and efficiency in the digital age.