Manuals / Cisco Systems / Computer Equipment / Network Hardware

Cisco Systems D200 DLP-D297 Perform a Manual Span Upgrade on an Unprotected Span, 19-83, Click OK

Models: D200

1 86

Download 86 pages 24.52 Kb

Page 83

DLP-D297 Perform a Manual Span Upgrade on an Unprotected Span

Chapter 19 DLPs D200 to D299

DLP- D297 Perform a Manual Span Upgrade on an Unprotected Span

Step 9 Verify that the transmit signal falls within the acceptable range. See Table 2-4 on page 2-17for STM-N card transmit and receive levels.

Step 10 Complete the “NTP-D19 Install Fiber-Optic Cables on Optical Cards” procedure on page 2-16to attach the fiber to the cards. Wait for the IMPROPRMVL alarm to clear and the cards to become active.

Step 11 When cards on each end of the span have been successfully upgraded and all the facility alarms (LOS, SD, or SF) are cleared, remove the Force switch:

a.In node view, click the Maintenance > Protection tabs.

b.In the Protection Groups area, click the protection group that contains the card/port you want to clear.

c.In the Selected Group area, click the card you want to clear.

d.In the Switch Commands area, choose Clear.

e.Click Yes in the confirmation dialog box.

Step 12 Repeat this task for any other spans in the 1+1 linear configuration.

Step 13 Return to your originating procedure (NTP).

DLP-D297 Perform a Manual Span Upgrade on an Unprotected Span

Purpose	This task manually upgrades unprotected spans to a higher optical rate.
Tools/Equipment	Higher-rate cards
	Compatible hardware necessary for the upgrade
Prerequisite Procedures	DLP-D60 Log into CTC, page 17-49
Required/As Needed	As needed
Onsite/Remote	Onsite
Security Level	Provisioning or higher

Warning Do not reach into a vacant slot or chassis while you install or remove a module or a fan. Exposed circuitry could constitute an energy hazard. Statement 206

Caution Upgrading unprotected spans will cause all traffic running on those spans to be lost.

Caution Removing the fiber will cause all traffic on the unprotected span to be lost.

Step 1 Remove the fiber from both endpoint nodes in the span.

Step 2 Remove the STM-N cards from both span endpoints.

Step 3 For both ends of the span, in node view, right-click each STM-N slot and choose Change Card. Step 4 In the Change Card dialog box, choose the new STM-N type.

Step 5 Click OK.

		Cisco ONS 15454 SDH Procedure Guide, R7.2
		Cisco ONS 15454 SDH Procedure Guide, R7.2
	October 2007			19-83
	October 2007			19-83

Image 83

Cisco Systems D200 manual DLP-D297 Perform a Manual Span Upgrade on an Unprotected Span, 19-83, DLP-D60 Log into CTC, page

Contents

DLPs D200 to D299 DLP-D201 Apply a Lock-OnDLP-D60 Log into CTC, page 19-119-2 DLP-D202 Apply a LockoutDLP-D60 Log into CTC, page beams or view directly with optical instruments. Statement DLP-D203 Clear a Lock-On or LockoutDLP-D201 Apply a Lock-On, page 19-1 or DLP-D202 Apply a Lockout, pagePurpose DLP-D205 Clean Fiber Connectors with CLETOP19-4 Prerequisite Procedures19-5 DLP-D206 Clean the Fiber AdaptersDLP-D207 Delete a Server Trail DLP-D60 Log into CTC, page DLP-D208 Change External Alarms Using the AIC-I CardDLP-D209 Change External Controls Using the AIC-I Card 19-6Step 5 Click Apply DLP-D210 Change AIC-I Card Orderwire Settings19-7 DLP-D60 Log into CTC, pageStep 4 Click Apply DLP-D211 Provision CE-1000-4 Ethernet Ports19-8 DLP-D60 Log into CTC, pagePrerequisite Procedures NTP-D24 Verify Card Installation, pageDLP-D212 Create a User Data Channel Circuit 19-9DLP-D60 Log into CTC, page DLP-D213 Provision the Card Mode for ML-Series Ethernet CardsDLP-D214 Change the Service State for a Port 19-10DLP-D60 Log into CTC, page DLP-D215 Consolidate Links in Network Viewthe Cisco ONS 15454 SDH Reference Manual 19-11To toggle link icons on and off, go to Step 19-12Step 9 To filter the links by class 19-13DLP-D60 Log into CTC, page DLP-D216 Change the STM-N Card ALS Maintenance SettingsDisplayed Link Classes 19-14SDH Reference Manual ParameterDescription OptionsFigure 19-4 Protection Operation on a Three-Node MS-SPRing DLP-D217 MS-SPRing Exercise Ring Test19-16 DLP-D60 Log into CTC, pageStep 5 Exercise the east port 19-17Purpose DLP-D218 Provision SNCP Ring Selectors During Circuit Creation19-18 Prerequisite ProceduresDLP-D60 Log into CTC, page DLP-D219 Provision a Low-Order Tunnel RouteDLP-D220 Provision E-Series Ethernet Ports 19-19page DLP-D221 Provision E-Series Ethernet Ports for VLAN MembershipCisco ONS 15454, Cisco ONS 15454 SDH, and Cisco ONS DLP-D221 Provision E-Series Ethernet Ports for VLAN MembershipDescription Setting19-21 VLAN SettingsPurpose DLP-D222 Provision G-Series Ethernet Ports19-22 Prerequisite ProceduresStep 4 Click Load DLP-D223 Download an Alarm Severity Profile19-23 DLP-D60 Log into CTC, pageb. Click OK DLP-D224 Adjust the Java Virtual Memory Heap Size19-24 Prerequisite ProceduresPurpose Tools/Equipment Prerequisite Procedures DLP-D225 Enable Alarm FilteringDLP-D60 Log into CTC, page 19-25Low-Order Tunnels.” DLP-D227 Disable Alarm FilteringDLP-D225 Enable Alarm Filtering, page DLP-D60 Log into CTC, page DLP-D229 View Circuits on a SpanDLP-D60 Log into CTC, page DLP-D230 Change a Circuit State19-27 DLP-D60 Log into CTC, page DLP-D231 Edit a Circuit Name19-28 Purpose DLP-D232 Change Active and Standby Span Color19-29 Prerequisite Proceduresc. Click Reset to Defaults DLP-D233 Edit SNCP Circuit Path SelectorsNTP-D44 Provision SNCP Nodes, page 19-30Purpose DLP-D234 Roll the Source or Destination of One Optical Circuit19-31 Prerequisite ProceduresClick Next 19-32Figure 19-7 Selecting a New Endpoint 19-33Figure 19-8 Viewing the Rolls Tab DLP-D363 Provision Regenerator-Section DCC Terminations, page19-34 DLP-D60 Log into CTC, pageClick Finish Figure 19-6 on page19-35 DLP-D60 Log into CTC, page 19-36Step 9 Complete one of the following 19-37Step 14 If you checked Route Automatically in Step 19-38Step 17 Click Finish 19-39Tools/Equipment 19-40Prerequisite Procedures Purpose19-41 Tools/Equipment 19-42Prerequisite Procedures Purpose19-43 Purpose DLP-D240 Cancel a RollPrerequisite Procedures DLP-D239 Delete a RollDLP-D60 Log into CTC, page DLP-D241 Clear an MS-SPRing Manual Ring Switch19-45 Step 3 Click CancelPurpose DLP-D242 Create an MS-SPRing on a Single Node19-46 Prerequisite Procedures19-47 DLP-D243 Create a VLANFigure 19-12 Reinitialization Tool 19-48DLP-D60 Log into CTC, page Step 6 Click Go 19-49Tools/Equipment 19-50Prerequisite Procedures PurposePrerequisite Procedures DLP-D246 Provision E-Series Ethernet Card Modeand Server Trails” procedure on page 19-51c. Click the Maintenance Protection tabs DLP-D247 Change an STM-N Card19-52 Prerequisite ProceduresDLP-D60 Log into CTC, page DLP-D249 Provision IP SettingsDLP-D248 Delete VLANs 19-53Step 2 Click the Provisioning Network General tabs 19-54Step 5 Click Yes in the confirmation dialog box 19-55Reboot Activity Active TCC2/TCC2P LEDsStandby TCC2/TCC2P LEDs 19-56a. Click the No Authentication button DLP-D250 Set Up or Change Open Shortest Path First Protocol19-57 Prerequisite ProceduresStep 5 Provision the OSPF priority and interval settings 19-58a. Click the No Authentication button DLP-D251 Set Up or Change Routing Information Protocol19-59 Prerequisite ProceduresPurpose DLP-D254 TCC2/TCC2P Card Active/Standby Switch Test19-60 Prerequisite ProceduresPurpose DLP-D255 Cross-Connect Card Side Switch Test19-61 Prerequisite ProceduresDLP-D60 Log into CTC, page DLP-D256 View Ethernet Statistics PM Parameters19-62 Step 8 Click SwitchDLP-D60 Log into CTC, page DLP-D257 View Ethernet Utilization PM ParametersCisco ONS 15454 SDH Reference Manual 19-63DLP-D60 Log into CTC, page DLP-D258 View Ethernet History PM ParametersDLP-D259 Refresh Ethernet PM Counts at a Different Time Interval 19-64Purpose DLP-D260 Set Auto-Refresh Interval for Displayed PM Counts19-65 Prerequisite ProceduresDLP-D60 Log into CTC, page DLP-D261 Refresh PM Counts for a Different PortDLP-D262 Filter the Display of Circuits 19-66Ring-Choose the ring from the drop-down list 19-67Purpose DLP-D263 Edit SNCP Dual-Ring Interconnect Circuit Hold-Off Timer19-68 Prerequisite Procedures19-69 Table 19-5 on page 19-69 for a list of cardsJ1 Function Cardsa. In the Edit Circuit window, click the Members tab 19-70e. Click Apply, then click Close 19-71DLP-D60 Log into CTC, page DLP-D265 Change the Login Legal DisclaimerCommand 19-72DLP-D60 Log into CTC, page DLP-D266 Change IP Settings19-73 DLP-D60 Log into CTC, page DLP-D268 Apply a Custom Network View Background Map19-74 DLP-D60 Log into CTC, page DLP-D269 Enable Dialog Box Do-Not-Display OptionDLP-D271 Change Node Security Policy on a Single Node 19-75Step 3 In the User Lockout area, you can modify the following 19-76Purpose DLP-D272 Change Node Security Policy on Multiple Nodes19-77 Prerequisite ProceduresStep 10 Click OK DLP-D273 Modify SNMP Trap Destination19-78 DLP-D60 Log into CTC, pageDLP-D60 Log into CTC, page DLP-D293 Perform a Manual Span Upgrade on a Two-Fiber MS-SPRing“DLP-D303 Initiate an MS-SPRing Force Ring Switch” task on page 19-79“DLP-D303 Initiate an MS-SPRing Force Ring Switch” task on page DLP-D294 Perform a Manual Span Upgrade on a Four-Fiber MS-SPRing19-80 Prerequisite ProceduresStep 6 Click OK DLP-D295 Perform a Manual Span Upgrade on an SNCP19-81 DLP-D60 Log into CTC, pagePurpose DLP-D296 Perform a Manual Span Upgrade on a 1+1 Protection Group19-82 Prerequisite ProceduresStep 5 Click OK DLP-D297 Perform a Manual Span Upgrade on an Unprotected Span19-83 DLP-D60 Log into CTC, pageDLP-D60 Log into CTC, page DLP-D298 Check the Network for Alarms and Conditions19-84 Purpose DLP-D299 Initiate an MS-SPRing Span Lockout19-85 Prerequisite ProceduresDLP- D299 Initiate an MS-SPRing Span Lockout 19-86Cisco ONS 15454 SDH Procedure Guide, R7.2 Chapter 19 DLPs D200 to D299