122F 50C Statement | Cisco Systems ME3600X24CXM specs

Chapter 2 Switch Installation

Warnings

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030

Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040

Warning For connections outside the building where the equipment is installed, the following ports must be connected through an approved network termination unit with integral circuit protection. 10/100/1000 Ethernet Statement 1044

Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last. Statement 1046

Warning No user-serviceable parts inside. Do not open. Statement 1073

Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074

Caution The intra-building port(s) of the equipment or subassembly is suitable for connection to intrabuilding or unexposed wiring or cabling only. The intra-building port(s) of the equipment or subassembly MUST NOT be metallically connected to interfaces which connect to the OSP or its wiring. These interfaces are designed for use as intra-building interfaces only (Type 2 or Type 4 ports as described in GR-1089-CORE, Issue 5) and require isolation from the exposed OSP cabling. The addition of Primary Protectors is not sufficient protection in order to connect these interfaces metallically to OSP wiring.

You can use the grounding lug to attach a wrist strap for ESD protection during servicing.

Warning To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of:

122•F (50•C) Statement 1047

Warning This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028

Cisco ME 3800X and ME 3600X Switch Hardware Installation Guide

	OL-22168-01	2-3

Image 23

Cisco Systems ME3600X24CXM manual 122F 50C Statement

Contents

Text Part Number OL-22168-01 Americas HeadquartersPage Purpose Audience Related Publications Obtaining Documentation and Submitting a Service Request OL-22168-01 Switch Models Setting Up the Switch Front Panel Switch Model Description Bits Port Alarm Input Port SFP+ and SFP Modules Management and Console Port10/100/1000 Gigabit Ethernet Ports Dwdm CAB-SFP-50CM Part Number Description SFP Module Patch Cable SD Memory SlotLEDs Color System Status Switch LED PanelsSystem LED Description Ethernet Management Port LED Description Power Supply Module Input LED DescriptionPower Supply and Fan LED Description SD Card LED Description Alarm LEDs DescriptionSync LED Description LED Color Meaning Rear PanelPort LEDs Description Power Supply Module LEDs Power Supply Module Features Fan Module Fan Module LED Management Options Network Configurations Switch Installation Switch Installation 122F 50C Statement Verifying Switch Operation Installation Guidelines Rack-Mounting Installing the SwitchPowering Off the Switch Rack-Mounting Brackets Attaching Brackets to the Switch Attaching Brackets for 19-Inch Racks Attaching Brackets for 23-Inch Racks Attaching Brackets for Etsi Racks Attaching Angle Brackets for 23-Inch Racks Mounting in a Rack Mounting the Switch Mounting the Switch Using 23-Inch Angle Brackets Attaching Brackets for Wall-Mounting Wall-Mounting Mounting Cisco ME 3800X on a Wall Mounting the Switch on a Wall Table- or Shelf-Mounting Installing and Removing SFP+ and SFP ModulesInstalling SFP+ and SFP Modules Removing SFP+ or SFP Modules 11 Installing an SFP+ Module into an SFP+ Module Slot 12 Removing a Bale-Clasp Latch SFP+ Module Inserting and Removing the SFP+ Module Patch Cable 14 Connecting Two Switches with an SFP+ Module Patch Cable 15 Connecting to an Ethernet Port Connecting to the 10/100/1000 Ports Where to Go Next Connecting to Fiber-Optic SFP+ and SFP Modules Model number Description Power Supply Module Description AC Input Power Supply Module Handle Side Fan Module Description Connector-Side Description Equipment That You Supply Power Supply and Fan Module InstallationInstallation Guidelines AC-1 PSU-1 AC-2 PSU-2 Installing an AC Power Supply Module AC Power Supply Module and Power-Cord Retainer in a Switch Removing AC Power Supply Modules Preparing for Installation Installing a DC Power Supply Module Stripping the Ground Wire Grounding the Switch Crimping the Ground Lug 24VDC 30A Installing the DC Power Supply Module in the SwitchWiring the DC Input Power Source Inch 8.9 mm ± 0.02 inch 0.5 mm 3 Wire lead Insulation Removing the DC Power Supply Module 14 Inserting a Fan Module in a Switch Installing a Fan Module OL-22168-01 Switch Post Results Diagnosing Problems Ethernet and Fiber Cables Switch LEDsSwitch Connections Bad or Damaged Cable Spanning Tree Loops SFP+ and SFP Module Port IssuesPort and Interface Settings Ping the End Device Autonegotiation and NICs Clearing the Switch IP Address and ConfigurationSwitch Performance Speed, Duplex, and Autonegotiation Serial Number Location on the Cisco ME 3800X and ME Finding the Switch Serial Number OL-22168-01 Environmental Ranges Technical Specifications DC Power Requirements Physical DimensionsAC Power Requirements Table A-3 Technical Specifications-ME-3600X-24FS-M Table A-4 Technical Specifications-ME-3600X-24TS-M Power Specifications Physical Specifications OL-22168-01 10/100/1000 Connector Specifications Copper SFP Module RJ-45 Connector SFP and SFP+ Module Connectors Figure B-5 SFP Module Patch Cable 10/100/1000 Ethernet Management Port TX TIP Pin Signal Direction Description Core Modal Wavelength Cables and AdaptersSFP and SFP+ Module Cabling Dwdm TP3 Cable Pinouts Figure B-11 Console Port Adapter Pinouts DSR DTR CTS RTS Switch Console RJ-45-to-DB-25 Port DTE OL-22168-01 Starting the Terminal-Emulation Software Accessing the CLI Through the Console Port Completing the Setup Program Entering the Initial Configuration InformationIP Settings Enter an enable password, and press Return These choices appear