Cisco Systems ME3600X24CXM B

B-1

Cisco ME 3800X and ME 3600X Switch Hardware Installation Guide

OL-22168-01

APPENDIX

Connector and Cable Specifications

•Connector Specifications, pageB-1

•Cables and Adapters, page B-5

Connector Specifications

•10/100/1000, pageB-1

•SFP and SFP+ Module Connectors, page B-2

•10/100/1000 Ethernet Management Port, pageB-3

•Alarm Input Port, page B-3

•BITS Port, page B-4

10/100/1000

The 10/100/1000 Ethernet ports use standard RJ-45 connectors and Ethernet pinouts.

FigureB-1 10/100/1000 Port Pinouts

60915

231 45678Pin Label

TP0+

TP0-

TP1+

TP2+

TP2-

TP1-

TP3+

TP3-

Contents

Main Page Preface Audience Purpose Related Publications Obtaining Documentation and Submitting a Service Request Page Product Overview Setting Up the Switch Switch Models Front Panel BITS Port Alarm Input Port Management and Console Port 10/100/1000 Gigabit Ethernet Ports SFP+ and SFP Modules Page SFP Module Patch Cable SD Memory Slot LEDs Switch LED Panels System LED Description Power Supply Module Input LED Description Power Supply and Fan LED Description Ethernet Management Port LED Description Alarm LEDs Description Sync LED Description SD Card LED Description Port LEDs Description Rear Panel Power Supply Module Features Power Supply Module LEDs Fan Module Fan Module LED Management Options Network Configurations Switch Installation Warnings 2-2 environment. Page Installation Guidelines Verifying Switch Operation Powering Off the Switch Installing the Switch Rack-Mounting Attaching Brackets to the Switch Attaching Brackets for 19-Inch Racks Attaching Brackets for 23-Inch Racks Attaching Brackets for ETSI Racks Attaching Angle Brackets for 23-Inch Racks Mounting in a Rack Mounting the Switch using 19-Inch, 23-Inch, and ETSI Brackets Mounting the Switch Using 23-Inch Angle Brackets Wall-Mounting Attaching Brackets for Wall-Mounting Mounting the Switch on a Wall Table- or Shelf-Mounting Installing and Removing SFP+ and SFP Modules Installing SFP+ and SFP Modules Removing SFP+ or SFP Modules Inserting and Removing the SFP+ Module Patch Cable 2-18 Cisco ME 3800X and ME 3600X Switch Hardware Installation Guide OL-22168-01 Chapter2 Switch Installation Inserting and Removing the SFP+ Module Patch Cable ALARMS CONSOLE Connecting to the 10/100/1000 Ports Connecting to Fiber-Optic SFP+ and SFP Modules Where to Go Next Installing and Removing AC and DC Input Power Supply and Fan Modules Power Supply Module Description Page Fan Module Description Connector-Side Description Power Supply and Fan Module Installation Equipment That You Supply Installation Guidelines 1 1 1 Installing an AC Power Supply Module AC-1 AC-2 PSU-1 PSU-2 Removing AC Power Supply Modules Installing a DC Power Supply Module Preparing for Installation Grounding the Switch Page Installing the DC Power Supply Module in the Switch Wiring the DC Input Power Source Page Removing the DC Power Supply Module Installing a Fan Module Page Troubleshooting Diagnosing Problems Switch POST Results Switch LEDs Switch Connections Bad or Damaged Cable Ethernet and Fiber Cables Link Status SFP+ and SFP Module Port Issues Port and Interface Settings Ping the End Device Spanning Tree Loops Switch Performance Clearing the Switch IP Address and Configuration Finding the Switch Serial Number Page A Technical Specifications Environmental and Technical Specifications for the Switch Page Page Page Environmental and Technical Specifications for the Power Supply and Fan Modules Page B Connector and Cable Specifications Connector Specifications 10/100/1000 B-2 SFP and SFP+ Module Connectors FigureB-2 Duplex LC Cable Connector FigureB-3 Simplex LC Cable Connector FigureB-4 Copper SFP Module RJ-45 Connector 231 45678Pin Label 10/100/1000 Ethernet Management Port The 10/100/1000 Ethernet management port uses standard RJ-45 connectors with Ethernet pinouts. FigureB-6 10/100/1000 Port Pinouts Alarm Input Port Note We recommend using a shielded cable grounded at both ends for NEBS. BITS Port Cables and Adapters SFP and SFP+ Module Cabling Page B-7 Cable Pinouts Console Port Adapter Pinouts Page Page C Configuring the Switch with the CLI-Based Setup Program Accessing the CLI Through the Console Port Starting the Terminal-Emulation Software Entering the Initial Configuration Information IP Settings Completing the Setup Program