OL-22168-01 | Cisco Systems ME3600X24CXM instruction

Appendix A Technical Specifications

Environmental and Technical Specifications for the Power Supply and Fan Modules

Cisco ME 3800X and ME 3600X Switch Hardware Installation Guide

	A-6	OL-22168-01

Image 66

Cisco Systems ME3600X24CXM manual OL-22168-01

Contents

Americas Headquarters Text Part Number OL-22168-01Page Audience Purpose Related Publications Obtaining Documentation and Submitting a Service Request OL-22168-01 Setting Up the Switch Switch Models Switch Model Description Front Panel Alarm Input Port Bits Port Management and Console Port 10/100/1000 Gigabit Ethernet PortsSFP+ and SFP Modules Part Number Description Dwdm CAB-SFP-50CM SD Memory Slot LEDsSFP Module Patch Cable Switch LED Panels System LED DescriptionColor System Status Power Supply Module Input LED Description Power Supply and Fan LED DescriptionEthernet Management Port LED Description Alarm LEDs Description Sync LED DescriptionSD Card LED Description Rear Panel Port LEDs DescriptionLED Color Meaning Power Supply Module Features Power Supply Module LEDs Fan Module Management Options Fan Module LED Network Configurations Switch Installation Switch Installation 122F 50C Statement Installation Guidelines Verifying Switch Operation Installing the Switch Powering Off the SwitchRack-Mounting Attaching Brackets to the Switch Rack-Mounting Brackets Attaching Brackets for 19-Inch Racks Attaching Brackets for 23-Inch Racks Attaching Brackets for Etsi Racks Attaching Angle Brackets for 23-Inch Racks Mounting the Switch Mounting in a Rack Mounting the Switch Using 23-Inch Angle Brackets Wall-Mounting Attaching Brackets for Wall-Mounting Mounting the Switch on a Wall Mounting Cisco ME 3800X on a Wall Installing and Removing SFP+ and SFP Modules Installing SFP+ and SFP ModulesTable- or Shelf-Mounting 11 Installing an SFP+ Module into an SFP+ Module Slot Removing SFP+ or SFP Modules Inserting and Removing the SFP+ Module Patch Cable 12 Removing a Bale-Clasp Latch SFP+ Module 14 Connecting Two Switches with an SFP+ Module Patch Cable Connecting to the 10/100/1000 Ports 15 Connecting to an Ethernet Port Connecting to Fiber-Optic SFP+ and SFP Modules Where to Go Next Power Supply Module Description Model number Description AC Input Power Supply Module Handle Side Connector-Side Description Fan Module Description Power Supply and Fan Module Installation Installation GuidelinesEquipment That You Supply Installing an AC Power Supply Module AC-1 PSU-1 AC-2 PSU-2 Removing AC Power Supply Modules AC Power Supply Module and Power-Cord Retainer in a Switch Installing a DC Power Supply Module Preparing for Installation Grounding the Switch Stripping the Ground Wire Crimping the Ground Lug Installing the DC Power Supply Module in the Switch Wiring the DC Input Power Source24VDC 30A Inch 8.9 mm ± 0.02 inch 0.5 mm 3 Wire lead Insulation Removing the DC Power Supply Module Installing a Fan Module 14 Inserting a Fan Module in a Switch OL-22168-01 Diagnosing Problems Switch Post Results Bad or Damaged Cable Switch LEDsSwitch Connections Ethernet and Fiber Cables Ping the End Device SFP+ and SFP Module Port IssuesPort and Interface Settings Spanning Tree Loops Speed, Duplex, and Autonegotiation Clearing the Switch IP Address and ConfigurationSwitch Performance Autonegotiation and NICs Finding the Switch Serial Number Serial Number Location on the Cisco ME 3800X and ME OL-22168-01 Technical Specifications Environmental Ranges Physical Dimensions AC Power RequirementsDC Power Requirements Table A-3 Technical Specifications-ME-3600X-24FS-M Table A-4 Technical Specifications-ME-3600X-24TS-M Physical Specifications Power Specifications OL-22168-01 Connector Specifications 10/100/1000 SFP and SFP+ Module Connectors Copper SFP Module RJ-45 Connector 10/100/1000 Ethernet Management Port Figure B-5 SFP Module Patch Cable Pin Signal Direction Description TX TIP Cables and Adapters SFP and SFP+ Module CablingCore Modal Wavelength Dwdm Cable Pinouts TP3 Console Port Adapter Pinouts Figure B-11 Switch Console RJ-45-to-DB-25 Port DTE DSR DTR CTS RTS OL-22168-01 Accessing the CLI Through the Console Port Starting the Terminal-Emulation Software Entering the Initial Configuration Information IP SettingsCompleting the Setup Program Enter an enable password, and press Return These choices appear