Manuals / Cisco Systems / Computer Equipment / Network Router

Cisco Systems MWR 1900 manual Connecting the Console Terminal and Modem, Attaching the Brackets

Models: MWR 1900

1 48

Download 48 pages 558 b

Page 24

Attaching the Brackets

Chapter 3 Installing the Router

Connecting the Console Terminal and Modem

Attaching the Brackets

Attach the mounting brackets to the chassis as shown, using the screws provided in the bracket kit. Attach the second bracket to the opposite side of the chassis. Use a number 2 Phillips screwdriver to install the bracket screws.

Four screws are required on each side. Figure 3-1shows how the bracket is attached.

Figure 3-1 Attaching the Bracket

BEFORE INSTALLATION

DSU 56K

SEE MANUAL BEFORE INSTALLATION

CO
NSOLE	A
	UXILIARY

65785

Rack-mount bracket

Installing the Router in the Rack

Install the chassis in the rack. Rack-mounting screws are not provided with the router. Use two screws for each side (supplied with the rack).

Installing a T1/E1 Multiflex VWIC

If your MWR 1900 router does not have a T1/E1 Multiflex VWIC installed of if you need to install an additional T1/E1 Multiflex VWIC, see the VWIC-2MFT-T1-DIR,VWIC-2MFT-E1-DIR Installation Instructions.

Caution T1/E1 Multiflex VWICs do not support online insertion and removal (hot swapping). Before inserting a card into the network module or router chassis, you must turn off electrical power and disconnect network cables.

Connecting the Console Terminal and Modem

This section describes how to connect a console terminal and a modem to the router. You can connect only a terminal to the console port. Use the auxiliary port with a terminal or a modem for remote access to the router.

Cisco MWR 1900 Mobile Wireless Edge Router Hardware Installation Guide

3-2	78-13982-02

Image 24

Cisco Systems MWR 1900 manual Connecting the Console Terminal and Modem, Attaching the Brackets

Contents

Corporate Headquarters Cisco Systems, Inc 170 West Tasman Drive San Jose, CA800 553-NETS Fax 408 Customer Order Number DOC-7813982= Text Part NumberTurn the television or radio antenna until the interference stops Required Tools and Equipment for Installation and Maintenance AudienceTechnical Assistance Center C O N T E N T STroubleshooting A-1 What to Do After Installing the HardwareProblem Solving Console Port ConnectionsAbout This Guide ObjectivesAudience OrganizationConventions boldface fontitalic font harm you. A warning symbol precedes each warning statement määräysten noudattaminen ja tietoa turvallisuudestaObtaining Documentation World Wide Webviii Obtaining Technical Assistance Ordering DocumentationDocumentation Feedback Cisco.comContacting TAC by Using the Cisco TAC Website Technical Assistance CenterContacting TAC by Telephone Overview of the Cisco MWR 1900 Router Primary Use of the MWRC H A P T E R Hardware Features Figure 1-1 MWR 1900 in an IP-RAN SolutionThe Cisco MWR 1900 router includes the following features Two DIMM-168 SDRAM 4 banks socketsSysAD bus speed and SDRAM local bus speed is 80Mhz External Compact Flash CF Two fixed LAN 10/100 Base-T Ethernet PortsFast Ethernet Interfaces Voice/WAN Interface CardsOverview of Cisco MWR 1900 Power Supplies Compact FlashSpecification Environmental Monitoring Temperature Sensor System SpecificationsRegulatory Compliance Preparing to Install the Router Safety RecommendationsC H A P T E R Safety with Electricity General Site Requirements Required Tools and Equipment for Installation and MaintenanceInspecting the Router Creating a Site LogCisco Information Packet publication Installation Checklist and Safety Information document receivedCisco Information Packet publication received TaskConsole and Auxiliary Port Considerations Console Port ConnectionsAuxiliary Port Connections Installing the Router Rack Mounting the ChassisC H A P T E R Connecting the Console Terminal and Modem Installing the Router in the RackInstalling a T1/E1 Multiflex VWIC Attaching the BracketsIdentifying a Rollover Cable Console PortFigure 3-2 Identifying a Rollover Cable Connecting the Network Cables Connecting the FE Interface CablesAuxiliary Port Connecting the VWIC Interface Cables Y-Cable Specifications Figure 3-4 RJ-48C ConnectionTable 3-2 RJ-48C Pinout Required Tools and Equipment Connecting the MWR 1900 Router to a DC-Input Power SupplyGrounding the Router Wire lead0.50 ± InsulationWiring the DC-Input Power Source Powering On the RouterReplacing or Upgrading the CF 3-10Installing a CF Memory Card in an External Slot Removing a CF Memory Card from an External Slot3-11 Formatting Procedures for CF Memory Cards File and Directory Proceduresdestination-filename command Formatting CF Memory as a DOS File SystemDisplay the Contents of a CF Card Display Geometry and Format Information3-13 Router# copy slot0mwr1900-i-mz.tmp tftpDelete Files from Flash Rename a File in Flash3-14 Router# show slot0Display File Content Create a New Directory3-15 What to Do After Installing the Hardware Remove a DirectoryEnter a Directory and Determine the Current Directory 3-16Troubleshooting Problem SolvingA P P E N D I X A Troubleshooting the Power and Cooling Systems Environmental Reporting FeaturesTroubleshooting Modules, Cables, and Connections Reading the LEDsTable A-2 Fast Ethernet Connector LEDs Figure A-1 Front Panel of the MWRTable A-3 VWIC LEDs Appendix A Troubleshooting Reading the LEDs 78-13982-02Numerics I N D EIN-1 IN-2 IN-3 IN-4 Index78-13982-02