Setting Up Network Module Interfaces | Cisco Systems NME-WAE

Setting Up Cisco WAE Network Modules and Opening a Session

If you lose power or connection during any of the following procedures, the software usually detects the interruption and tries to recover. If it fails to recover, reinstall the software using the boothelper.

You can configure basic network parameters for the network module by using the CLI, which is described in this document. For additional configuration instructions, see the ACNS online help that is included with the software application.

Setting Up Network Module Interfaces

Your first configuration task is to configure the network module interfaces to the host router and to its external links. You use these interfaces to access the module for installing and configuring the ACNS software application.

This section includes the following topics:

•Summary Steps

•Detailed Steps

•Examples

The first several steps open the host router CLI to the module. The subsequent steps configure the interface.

Summary Steps

The network module is referred to as the integrated service engine (ISE) on the IOS CLI.

From the host router CLI, use the following commands:

1.enable

2.configure terminal

3.interface integrated-service-engine slot/0

4.ip address router-side-ip-address subnet-mask

5.service-module ip address module-side-ip-address subnet-mask or

service-module external ip address module-side-ip-addresssubnet-mask

6.service-module ip default-gateway gateway-ip-address

7.end

8.copy running-config startup-config

9.show running-config

Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments

6	OL-13140-02

Image 6

Cisco Systems NME-WAE manual Setting Up Network Module Interfaces, Summary Steps Detailed Steps Examples

Contents

Contents Prerequisites for Installing the Cisco WAE Network Modules Restrictions for Cisco WAE Network Modules Faceplate and LEDs Hard Disk and Memory SpecificationsCisco WAE Network Module Hardware Description Model Hard Disk Memory Shutdown CF card Hardware Interfaces Using ThisOn This Hardware Interface Configure These Settings This section contains the following topics Setting Up Network Module Interfaces Summary Steps Detailed Steps Examples Procedure Command Example Verify interface configurations Save the router running configurationDisplay the router running configuration so that you can Opening and Closing a Network Module Session Press Control-Shift-6 Example Configuration Press Ctrl-Shift-6 Accessing the Acns Software on the Network Module Configuration Mode Command PurposeShutting Down and Starting Up Cisco WAE Network Modules Displaying Status and Diagnostic Output Command Purpose Displays general information about Service module. This information is useful toCisco technical support for problem Diagnosis Command Reference Syntax Description Defaults Command Modes Command History Interface integrated-service-engineInterface integrated-service-engine slot/unit ReleaseModification Bootloader to perform startup routines Service-module integrated-service-engine default-bootDefaults Command Modes Command History None Privileged Exec Command Description Service-module integrated-service-engine reloadService-module integrated-service-engine slot/unit reload Usage Guidelines Related Commands Description Service-module integrated-service-engine resetService-module integrated-service-engine slot/unit reset Router# service-module integrated-service-engine 1/0 reset Command Description Service-module integrated-service-engine session OpenUsername Related Commands Description Interface integrated-service-engine Service-module integrated-service-engine shutdownService-module integrated-service-engine slot/unit shutdown Integrated-service-engine reset Command Description Service-module integrated-service-engine statistics Access router Router# service-module integrated-service-engine 1/0 status Service-module integrated-service-engine statusService-module integrated-service-engine slot/unit status Display the ISE network module software release version Related Commands Description Show controllers integrated-service-engine Show controllers integrated-service-engine slot/unitField Description Related Commands Description Show diag Show diag slotRelease Modification Show diag subslot Field Descriptions Displays basic interface configuration information for Integrated-service-engine network modulesNetwork modules Show interfaces integrated-service-engine Show interfaces integrated-service-engine slot/unitCommand Modes Command History Field Description Errors created when the CRC generated by the originating LAN Station that is transmitting bad data Field Description Glossary BoothelperBootloader Blade Engine Syslog Service or servicesRelated Documentation Related Topic Document TitlePage OL-13140-02