Terminals to black terminals | Classe Audio SSP-800 instruction

Step 5

Important!

26

Connect the Main Analog Audio Outputs, either RCA or XLR, from the rear panel of the SSP-800 to the corresponding inputs on your ampliﬁer(s) as follows:

•Connect the SSP-800 Front Left and Front Right outputs to the inputs of the ampliﬁer(s) designated for the Front Left and Front Right speakers, respectively.

•Connect the SSP-800 centre output to the input of the ampliﬁer designated for the centre channel speaker.

•Connect the SSP-800 Left Surround and Right Surround outputs to the inputs of the ampliﬁer(s) designated for the Left Surround and Right Surround speakers, respectively.

•If you are setting up a 7.1-channel system, then also connect the SSP-800 Left Rear and Right Rear outputs to the inputs of the ampliﬁer(s) designated for the Left Rear and Right Rear speakers, respectively.

•If you are using a subwoofer, connect the SSP-800 subwoofer output to the input of the designated ampliﬁer or powered subwoofer.

NOTE: Make sure connections from the subwoofer output go only to an ampliﬁer connected to a subwoofer, as low frequency signals can damage a small full-range speaker not designed for high output bass reproduction.

Verify that each cable is clearly labeled so that you don’t mix them up. When connecting a cable, make sure the cable has a good connection and is ﬁrmly attached to the rear panel connectors on both the ampliﬁer and the SSP-800.

The SSP-800 also provides two Auxiliary analog audio outputs. See the Rear Panel section for more details about the Auxiliary outputs.

Connect the loudspeakers to the amplifiers.

Verify that the power amplifier(s) is plugged in but powered OFF before connecting to the SSP-800!

Connect each loudspeaker to its designated ampliﬁer(s) channel. Pay close attention to the phase of the speaker connections – always connect an ampliﬁer’s red (+) terminals to the red (+) terminals of the loudspeaker. Likewise, connect black

(–) terminals to black (–) terminals.

Image 26

Classe Audio SSP-800 owner manual Terminals to black terminals

Contents

SSP-800 Surround Sound Processor Page Important Safety Instructions Contents Configuration Use Video Next input Introduction Welcome to the Classé family Exceptional Design Features Page Unpacking and Placement Unpacking your SSP-800 Placement considerations Warm-up/break-in period Operating voltage Voltage protection Front Panel Standby/On SwitchMenu On/Off Switch Audio Mute Control Volume Control KnobTouchscreen IR window Rear Panel Video Inputs Hdmi Inputs Composite Video InputsComponent Video Inputs Digital Audio Inputs Coaxial Hdmi OutputsComponent Video Output Digital Audio Inputs Optical 11 7.1-Channel Analog Audio Inputs Digital Audio Output CoaxialDigital Audio Output Optical 12 2-Channel Balanced Analog Audio Inputs Trigger Outputs IR InputIR Output USB Port 18 RS-232 Port CAN-Bus Input and Output 20 10-Channel Analog Outputs Main Power On/Off Switch AC Power Cord Input Audio Processing Functions Remote ControlBasic Functions Input Sel Selection Button Navigation & Menu Buttons Preset Config Configuration ButtonVolume Control & Mute Buttons Function Keys F1 to F4 Choose the appropriate cables Initial SetupStep Connect all source components to the SSP-800 rear panel Terminals to black terminals Power up the system Understanding Surround Sound Name Post-processing DTS-HD Using the SSP-800 Source selection Mode selection Name Description Data in the soundtrack Controls System trims Configuration select Menu System System setup Volume setup Max volume Startup volume IR setup Automation Mute setup Input setup Name Audio Configuration Use Video Next input Triggers Profiles Room EQ Configuration Name Distances Levels Use Speakers Speakers available Auxiliary channels Black level Teach IR Display setup Brightness Timeout Language OSD on screen display Colors Volume Dolby/DTS Dolby Pro Logic DTS Neo6 Remote Fkeys Important note on Fkey use Features Version info Sensors Category 5 Network Cables Hardware setupClassé Delta Series Products CAN-Bus Terminator SSP-300 & 600 CAN-Bus Interface Box Using CAN-Bus CAN-Bus shared features Configuration Operate AC status Status PlayLink Amp info Event log There is no sound and the Standby LED is not lit TroubleshootingEverything appears to be powered on, but there is no sound There is a hum coming out of the speakers IR remote control does not seem to functionOnly one speaker seems to be playing There is a hum coming from the SSP-800 Voltage Protection Circuit Care & Maintenance Input factory defaults Net weight SpecificationsOverall dimensions Shipping weight Dimensions Installation Worksheet Page North America 1 800 370 3740 email classe@bwgroupusa.com