ClearOne comm 900, 600 STEREOMIX - Sets the Input to be a Stereo Mix, SYSCHECKS - System Checks

112 Appendix — Serial Commands

STEREOMIX - Sets the Input to be a Stereo Mix

This command enables/disables or reports the stereo mix status of an input.

ARGUMENT DETAILS

Name	Type	Size	Values		Units
Channel	Channel	1	See Group and Channels
Group	Group	1	7	(L)
Value	Unsigned Integer	2	0	= On
			1	= Off
			2	= Toggle
			(NULL to query in text)
BINARY FORM DETAILS
COMMAND ID:		86
NUMBER OF ARGUMENTS: 1
ARGUMENT FORM:		<Channel><Group><Value>

TEXT FORM DETAILS

COMMAND FORM:DEVICE STEREOMIX <Channel> [Value]

SYSCHECKS - System Checks

Initiates the system checks.There is no query for this command.

ARGUMENT DETAILS

Name	Type	Size	Values		Units
System	Hexadecimal Integer	4	00 - Pod 1
			01	- Pod 2
			02	- Pod 3
			03	- Speaker
			04	- Telephone
			05	- Network
			06	- RF Remote (not implemented)
			All other bits reserved
Check	Integer
BINARY FORM DETAILS
COMMAND ID:		87
NUMBER OF ARGUMENTS: 1
ARGUMENT FORM:		<System Check>
TEXT FORM DETAILS
COMMAND FORM:		DEVICE SYSCHECKS <System Check>

Appendix— Serial Commands 113

SYSRESULT - System Check Result

This command reports the results of the system check.This command is reportable only. It cannot be queried or set.

ARGUMENT DETAILS

Name	Type	Size		Values
System Check	Hexadecimal Integer	2		06 – Remote (not implemented)
				05 – Network
				04 – Telephone
				03 – Speaker
				02 – Pod 3
				01 – Pod 2
				00 – Pod 1
				All other bits reserved.
Status	Unsigned Integer	2		0 = Fail
				1 = Pass
Message	String	40		For the pods: this message will say if a pod
				is not connected. If a pod is connected, the
				message will say which microphones fail. If
				none fail, the message will say the pod
				passes. For the speakers: the message will
				say if the speakers fail. If they, pass but are
				out of phase, the message will say they are
				out of phase. Otherwise, the message will say
				the speakers pass.
				For the telephone on hook: the message will
				report the line voltage, the line current,
				other results, and if dial tone is detected.For
				the telephone off hook: the message will
				report the line current, other results, and if
				dial tone is detected.The bit mask for the
				other results is
	X	X X X X	X X X
					set if switched from CTR21 to FCC because of low current
					set if used DIAL bit while dialing
					set if switch from Low Voltage to Japan because of current
					set if switch from Low Voltage to FCC because of current
					DAA OVL status
					DAA DOD status
					DAA OPD status
					Not used
				For the network check: the box will report if
				no IP address is set. If it is set, the box will
				ping the gateway.The message will say the
				ping failed if it is not returned in 5 s.
				Otherwise, the message will report how
				many seconds it took to return the ping.
BINARY FORM DETAILS
COMMAND ID:	88
NUMBER OF ARGUMENTS: 11
ARGUMENT FORM:	<System Check><Status><Message>
TEXT FORM DETAILS
COMMAND FORM:	DEVICE SYSRESULT <System Check> <Status> <Message>

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760 Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760