Manuals / ClearOne comm / Computer Equipment / Network Card

ClearOne comm AP10 operation manual Technical Services Group ~ 1-800-283-5936 USA ~

Models: AP10

1 40

Download 40 pages 23.96 Kb

Page 2

Image 2

rights reserved. No part of this document may

be reproduced in any form or by any means

without written permission from ClearOne

Communications, Inc. Printed in the United

States of America. ClearOne Communications

reserves specific privileges. Information in this

document is subject to change without notice.

AP10 Installation and Operation

Manual

ClearOne Part No. 800-150-201

June 2002 (Rev. 2.0)

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Page 2

Image 2

ClearOne comm AP10 operation manual Technical Services Group ~ 1-800-283-5936 USA ~

Contents

Installation & Operation Manual AP10 Telephone InterfaceTechnical Services Group ~ 1-800-283-5936 USA ~ CHAPTER 1 Introduction CHAPTER 3 ConfigurationCHAPTER 2 Installation AP10 Installation and Operation ManualAPPENDICES CHAPTER 4 OperationFeatures CHAPTER 1 IntroductionTechnical Support Professional Services GroupSales and Customer Service ClearOne Communications EuMEA GmbHFront view UnpackingControls and Connections Introduction ~ Controls and ConnectionsIntroduction ~ Controls and Connections Rear viewAB CD EF G Equipment placement Before You InstallPower requirements Introduction ~ Before You InstallTechnical Services Group ~ 1-800-283-5936 USA ~ Connect the unit CHAPTER 2 InstallationHardware Setup AP800three terminals in Installation ~ Hardware SetupCreating a G-Link network groundAssigning device ID numbers Connecting powerDevice ID DIP switch settings Installation ~ Hardware SetupTechnical Services Group ~ 1-800-283-5936 USA ~ Noise burst/auto-adapt CHAPTER 3 ConfigurationDIP Switch Settings Receive boostenabled Configuration ~ DIP Switch Settingsswitch 4 must be off down Receive AGCCalibration Configuration ~ CalibrationReceive reduction Noise burst adaptConfiguration ~ Calibration Transmit level adjustmentReceive level adjustment usingCHAPTER 4 Operation Using the AP10enabled DIP To answer a callDetailed instructions on creating site files and using AP-Ware can be Using the Telco InterfaceOperation ~ Using the Telco Interface in the AP-Ware help fileControllers To muteOther telco options Custom control through DB-25 portTechnical Services Group ~ 1-800-283-5936 USA ~ Appendix A Specifications APPENDICESAppendices ~ Appendix B Pinouts Remote connector pinoutAppendix B Pinouts Pin DescriptionAppendix C Serial Commands Set connector pinoutLine connector pinout ConventionsExample Command structureAppendices ~ Appendix C Serial Commands COMMANDDIAL AP10 Serial CommandsAppendices ~ Appendix C Serial Commands CommandAppendices ~ Appendix C Serial Commands HOOKHOOKD Command form DEVICE HOOKCommand form DEVICE LVL CH MUTEAppendices ~ Appendix C Serial Commands Command form DEVICE MUTE CH ExplanationTERL NULLRING Appendices ~ Appendix C Serial CommandsCommand form DEVICE TERLE TERLEAppendices ~ Appendix C Serial Commands Command form DEVICE UIDTHIS WARRANTY IS VOID IF Appendix D WarrantyAppendices ~ Appendix D Warranty Appendices ~ Appendix D Warranty FCC Part 68 Compliance Appendix E ComplianceFCC Part 15 Compliance Appendices ~ Appendix E ComplianceAppendices ~ Appendix E Compliance Safety InformationIC Compliance Ringer Equivalence Number REN 0.6BTechnical Services Group ~ 1-800-283-5936 USA ~ Appendix F Block DiagramAppendices ~ Appendix F Block Diagram G-LINKGlossary GlossaryGlossary Index Index