Manuals / ClearOne comm / Computer Equipment / Network Card

ClearOne comm AP10 operation manual Glossary

Models: AP10

1 40

Download 40 pages 23.96 Kb

Page 38

Glossary

34

Glossary

Matrix mixer A mixer that allows routing of any input or combination of inputs to an output or any combination of outputs.

Omni-directional Microphone A microphone that picks up audio in a 360-degree

pattern.

Reverberation Audio in a room that bounces off a wall, ceiling, table or other objects and then is picked up by microphone. High reverberation causes listener fatigue and makes audio difficult to understand.

Simultaneous Two Wire/Four Wire The ability of a teleconferencing device to connect to a video codec and a telephone line simultaneously.

Sound Pressure Level (SPL) The measure of acoustical audio in the air. Is measured in dB using an SPL meter.

Telephone Hybrid A term used to refer to a telephone interface that separates send and receive audio. Same as a digital hybrid.

Two Wire Typically refers to a telephone line.

Uni-directional Microphone A microphone that picks up audio in a directional (usually 180 degrees or less) pattern.

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 38

ClearOne comm AP10 operation manual Glossary

Contents

Installation & Operation Manual AP10 Telephone InterfaceTechnical Services Group ~ 1-800-283-5936 USA ~ CHAPTER 1 Introduction CHAPTER 3 ConfigurationCHAPTER 2 Installation AP10 Installation and Operation ManualAPPENDICES CHAPTER 4 OperationFeatures CHAPTER 1 IntroductionTechnical Support Professional Services GroupSales and Customer Service ClearOne Communications EuMEA GmbHFront view UnpackingControls and Connections Introduction ~ Controls and ConnectionsIntroduction ~ Controls and Connections Rear viewAB CD EF G Equipment placement Before You InstallPower requirements Introduction ~ Before You InstallTechnical Services Group ~ 1-800-283-5936 USA ~ Connect the unit CHAPTER 2 InstallationHardware Setup AP800three terminals in Installation ~ Hardware SetupCreating a G-Link network groundAssigning device ID numbers Connecting powerDevice ID DIP switch settings Installation ~ Hardware SetupTechnical Services Group ~ 1-800-283-5936 USA ~ Noise burst/auto-adapt CHAPTER 3 ConfigurationDIP Switch Settings Receive boostenabled Configuration ~ DIP Switch Settingsswitch 4 must be off down Receive AGCCalibration Configuration ~ CalibrationReceive reduction Noise burst adaptConfiguration ~ Calibration Transmit level adjustmentReceive level adjustment usingCHAPTER 4 Operation Using the AP10enabled DIP To answer a callDetailed instructions on creating site files and using AP-Ware can be Using the Telco InterfaceOperation ~ Using the Telco Interface in the AP-Ware help fileControllers To muteOther telco options Custom control through DB-25 portTechnical Services Group ~ 1-800-283-5936 USA ~ Appendix A Specifications APPENDICESAppendices ~ Appendix B Pinouts Remote connector pinoutAppendix B Pinouts Pin DescriptionAppendix C Serial Commands Set connector pinoutLine connector pinout ConventionsExample Command structureAppendices ~ Appendix C Serial Commands COMMANDDIAL AP10 Serial CommandsAppendices ~ Appendix C Serial Commands CommandAppendices ~ Appendix C Serial Commands HOOKHOOKD Command form DEVICE HOOKCommand form DEVICE LVL CH MUTEAppendices ~ Appendix C Serial Commands Command form DEVICE MUTE CH ExplanationTERL NULLRING Appendices ~ Appendix C Serial CommandsCommand form DEVICE TERLE TERLEAppendices ~ Appendix C Serial Commands Command form DEVICE UIDTHIS WARRANTY IS VOID IF Appendix D WarrantyAppendices ~ Appendix D Warranty Appendices ~ Appendix D Warranty FCC Part 68 Compliance Appendix E ComplianceFCC Part 15 Compliance Appendices ~ Appendix E ComplianceAppendices ~ Appendix E Compliance Safety InformationIC Compliance Ringer Equivalence Number REN 0.6BTechnical Services Group ~ 1-800-283-5936 USA ~ Appendix F Block DiagramAppendices ~ Appendix F Block Diagram G-LINKGlossary GlossaryGlossary Index Index