Manuals / ClearOne comm / Computer Equipment / Network Card

ClearOne comm AP10 operation manual Using the Telco Interface, in the AP-Ware help file, found

Models: AP10

1 40

Download 40 pages 23.96 Kb

Page 20

Operation ~ Using the Telco Interface

16	Operation ~ Using the Telco Interface

3.When the conversation is complete, press the Off button [E] to disconnect the call. You can also disconnect using an external controller. If the handset is off hook, audio will be routed to the telephone.

If your call is through the handset only (the red Off LED will be lit), hang up when the conversation is complete.

Using the Telco Interface

To make and disconnect a call

1.Open AP-Ware and select the AP10 unit.

2.Click the AP10 Telco button on the Flow Screen to open the Telco interface.

✍

found

Detailed instructions on creating site files and using AP-Ware can be

in the AP-Ware help file.

Figure 4.2. Telco dialing interface

3.Activate the telephone interface by clicking On or by beginning to dial.

4.When the green light below the On button illuminates, enter the number to be dialed, including any dial-out prefixes.

5.Click Send. If you clicked directly on the number buttons, the call will be completed as you finish dialing—just like using a standard telephone.

6.When you are finished with the call, click Disconnect to end the call.

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 20

ClearOne comm AP10 in the AP-Ware help file, Operation ~ Using the Telco Interface, To make and disconnect a call

Contents

Installation & Operation Manual AP10 Telephone InterfaceTechnical Services Group ~ 1-800-283-5936 USA ~ CHAPTER 3 Configuration CHAPTER 2 InstallationCHAPTER 1 Introduction AP10 Installation and Operation ManualAPPENDICES CHAPTER 4 OperationFeatures CHAPTER 1 IntroductionProfessional Services Group Sales and Customer ServiceTechnical Support ClearOne Communications EuMEA GmbHUnpacking Controls and ConnectionsFront view Introduction ~ Controls and ConnectionsIntroduction ~ Controls and Connections Rear viewAB CD EF G Before You Install Power requirementsEquipment placement Introduction ~ Before You InstallTechnical Services Group ~ 1-800-283-5936 USA ~ CHAPTER 2 Installation Hardware SetupConnect the unit AP800Installation ~ Hardware Setup Creating a G-Link networkthree terminals in groundConnecting power Device ID DIP switch settingsAssigning device ID numbers Installation ~ Hardware SetupTechnical Services Group ~ 1-800-283-5936 USA ~ CHAPTER 3 Configuration DIP Switch SettingsNoise burst/auto-adapt Receive boostConfiguration ~ DIP Switch Settings switch 4 must be off downenabled Receive AGCConfiguration ~ Calibration Receive reductionCalibration Noise burst adaptTransmit level adjustment Receive level adjustmentConfiguration ~ Calibration usingUsing the AP10 enabled DIPCHAPTER 4 Operation To answer a callUsing the Telco Interface Operation ~ Using the Telco InterfaceDetailed instructions on creating site files and using AP-Ware can be in the AP-Ware help fileTo mute Other telco optionsControllers Custom control through DB-25 portTechnical Services Group ~ 1-800-283-5936 USA ~ Appendix A Specifications APPENDICESRemote connector pinout Appendix B PinoutsAppendices ~ Appendix B Pinouts Pin DescriptionSet connector pinout Line connector pinoutAppendix C Serial Commands ConventionsCommand structure Appendices ~ Appendix C Serial CommandsExample COMMANDAP10 Serial Commands Appendices ~ Appendix C Serial CommandsDIAL CommandHOOK HOOKDAppendices ~ Appendix C Serial Commands Command form DEVICE HOOKMUTE Appendices ~ Appendix C Serial CommandsCommand form DEVICE LVL CH Command form DEVICE MUTE CH ExplanationNULL RINGTERL Appendices ~ Appendix C Serial CommandsTERLE Appendices ~ Appendix C Serial CommandsCommand form DEVICE TERLE Command form DEVICE UIDTHIS WARRANTY IS VOID IF Appendix D WarrantyAppendices ~ Appendix D Warranty Appendices ~ Appendix D Warranty Appendix E Compliance FCC Part 15 ComplianceFCC Part 68 Compliance Appendices ~ Appendix E ComplianceSafety Information IC ComplianceAppendices ~ Appendix E Compliance Ringer Equivalence Number REN 0.6BAppendix F Block Diagram Appendices ~ Appendix F Block DiagramTechnical Services Group ~ 1-800-283-5936 USA ~ G-LINKGlossary GlossaryGlossary Index Index