Manuals / ClearOne comm / Computer Equipment / Network Card

ClearOne comm AP10 Unpacking, Controls and Connections, Front view, Ab Cd E, half-second, while

Models: AP10

1 40

Download 40 pages 23.96 Kb

Page 7

Introduction ~ Controls and Connections

Introduction ~ Controls and Connections

Unpacking

Ensure that the following items were received with your shipment:

Figure 1.1. AP10 unpacking diagram

3

ClearOne is not responsible ! for product damage incurred during shipment.

You must make claims directly with the carrier. Inspect your shipment carefully for obvious signs of damage. If the shipment appears to be damaged, retain the original boxes and packing material for inspection by the carrier. Contact your carrier immediately.

Controls and Connections

AB CD E

Figure 1.2. AP10 front panel controls

Front view

A.DIP switches. Operational features can be enabled or disabled via DIP switches behind this panel. These features include auto-answer, auto-disconnect, momentary or latching mode, device identification, caller AGC, caller boost, and noise burst adapt/self adapt.

B.Transmit LED. This bicolor LED indicates the audio levels being transmitted from the room to the telephone line.

C.Receive LED. This bicolor LED indicates the audio level the room is receiving from the telephone line.

D.On. The On button connects the AP10 to the telephone line (dependent upon DIP switch settings) and automatically adapts the hybrid to the line. The LED will illuminate green when the hybrid is in the On state.

E.Off. The Off button disconnects the hybrid from the telephone line and mutes all audio. The LED indicates the hybrid’s Off state. The LED will illuminate red when the hybrid is in the Off state.

✍	Pressing and	holding	the
✍	On button for more than a
	half-second	while	the

hybrid is active will readapt the hybrid.

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 7

ClearOne comm AP10 Unpacking, Front view, Introduction ~ Controls and Connections, Ab Cd E, half-second, while

Contents

AP10 Telephone Interface Installation & Operation ManualTechnical Services Group ~ 1-800-283-5936 USA ~ AP10 Installation and Operation Manual CHAPTER 3 ConfigurationCHAPTER 2 Installation CHAPTER 1 IntroductionCHAPTER 4 Operation APPENDICESCHAPTER 1 Introduction FeaturesClearOne Communications EuMEA GmbH Professional Services GroupSales and Customer Service Technical SupportIntroduction ~ Controls and Connections UnpackingControls and Connections Front viewAB CD EF G Rear viewIntroduction ~ Controls and Connections Introduction ~ Before You Install Before You InstallPower requirements Equipment placementTechnical Services Group ~ 1-800-283-5936 USA ~ AP800 CHAPTER 2 InstallationHardware Setup Connect the unitground Installation ~ Hardware SetupCreating a G-Link network three terminals inInstallation ~ Hardware Setup Connecting powerDevice ID DIP switch settings Assigning device ID numbersTechnical Services Group ~ 1-800-283-5936 USA ~ Receive boost CHAPTER 3 ConfigurationDIP Switch Settings Noise burst/auto-adaptReceive AGC Configuration ~ DIP Switch Settingsswitch 4 must be off down enabledNoise burst adapt Configuration ~ CalibrationReceive reduction Calibrationusing Transmit level adjustmentReceive level adjustment Configuration ~ CalibrationTo answer a call Using the AP10enabled DIP CHAPTER 4 Operationin the AP-Ware help file Using the Telco InterfaceOperation ~ Using the Telco Interface Detailed instructions on creating site files and using AP-Ware can beCustom control through DB-25 port To muteOther telco options ControllersTechnical Services Group ~ 1-800-283-5936 USA ~ APPENDICES Appendix A SpecificationsPin Description Remote connector pinoutAppendix B Pinouts Appendices ~ Appendix B PinoutsConventions Set connector pinoutLine connector pinout Appendix C Serial CommandsCOMMAND Command structureAppendices ~ Appendix C Serial Commands ExampleCommand AP10 Serial CommandsAppendices ~ Appendix C Serial Commands DIALCommand form DEVICE HOOK HOOKHOOKD Appendices ~ Appendix C Serial CommandsCommand form DEVICE MUTE CH Explanation MUTEAppendices ~ Appendix C Serial Commands Command form DEVICE LVL CHAppendices ~ Appendix C Serial Commands NULLRING TERLCommand form DEVICE UID TERLEAppendices ~ Appendix C Serial Commands Command form DEVICE TERLEAppendices ~ Appendix D Warranty Appendix D WarrantyTHIS WARRANTY IS VOID IF Appendices ~ Appendix D Warranty Appendices ~ Appendix E Compliance Appendix E ComplianceFCC Part 15 Compliance FCC Part 68 ComplianceRinger Equivalence Number REN 0.6B Safety InformationIC Compliance Appendices ~ Appendix E ComplianceG-LINK Appendix F Block DiagramAppendices ~ Appendix F Block Diagram Technical Services Group ~ 1-800-283-5936 USA ~Glossary GlossaryGlossary Index Index