18-IN.

18-IN.

COOLING UNIT

18-IN.

AIR FLOW

(OPEN TO ROOM)

FIGURE 4. COOLING UNIT SPACE REQUIRED

PLACING COOLING UNIT IN OPERATING POSITION

1.Very carefully, move Cooling Unit back into operating position leaving space around Unit (see Figure 4) as specified in SELECTING LOCATION. MAKE SURE THERE ARE NO KINKS IN COOLING UNIT INLET LINES, AND (IF APPLICABLE) REMOTE CONDENSER AND FAN ASSEMBLY REFRIGERATION LINES.

NOTE: To comply with National Sanitation Foundation (NSF) requirements, Cooling Unit not installed on optional Cooling Unit Stand (P/N 309309-069) must have its base sealed to floor with Dow-Corning RTV 731 or equivalent.

2.Tilt Cooling Unit up to expose bottom of Unit base.

3.Liberally apply silastic sealant such as Dow-Corning (RTV 731) or equivalent on Unit base bottom edges.

NOTE: Do not move Cooling Unit after positioning or seal from Unit base to floor will be broken.

4.Lower Cooling Unit into operating position to complete seal from Unit base to floor. Apply additional sealant around bottom of base. Seal must have a minimum radius of 1/2-inch to prevent cracks and crevices and to ensure a complete seal.

5.Route Cooling Unit water tank overflow hose to permanent floor drain.

6.Seal area around drain and overflow hoses where they exit from Unit using Dow Corning (RTV 731) or equivalent).

PREPARING COOLING UNIT FOR OPERATION

1. Make sure plug in end of Cooling Unit water tank drain hose is secure.

Note: Some Cooling Units are equipped with a water tank water level float control. Open shutoff valve in plain water inlet supply line. Due to slow water fill rate of the water level float control, water tank may be hand filled until water runs out of the water tank overflow hose. CLEAN LOW-MINERAL-CONTENT WATER MUST BE USED WHERE A LOCAL WATER PROBLEM EXIST.

2.Fill water tank with clean water until water starts flowing from water tank overflow hose. USE LOW MINERAL CONTENT WATER WHERE A LOCAL WATER PROBLEM EXISTS.

3.Open shutoff valve in plain water inlet supply line.

4.Adjust primary CO2 regulator (see Figure 2) on CO2 cylinder to a minimum nominal setting of 120-psi or 24-psi higher than highest setting required by the secondary CO2 regulators. Loosen CO2 regulator adjusting screw locknut. Turn adjusting screw to the right (clockwise) until regulator gage registers nominal 120-psi, then tighten adjusting screw locknut.

300614000

10

Page 13 Page 15
Page 14
Image 14
Cornelius 10, 000 PLUS installation manual Placing Cooling Unit in Operating Position, Preparing Cooling Unit for Operation
Page 13 Page 15

000 PLUS, 10 specifications

Cornelius 10,000 PLUS is a pioneering innovation in the beverage dispensing industry, designed to cater to the evolving needs of commercial establishments. This advanced system combines state-of-the-art technology with user-friendly features, making it a standout choice for restaurants, cafes, and bars aiming to enhance their beverage service.

One of the main features of the Cornelius 10,000 PLUS is its impressive capacity. With the ability to dispense a wide variety of beverages, including soft drinks, cocktails, and craft beers, the system supports a large volume of service, perfect for high-demand environments. The modular design allows for easy expansion, enabling businesses to add additional flavors or beverages as needed without major overhauls.

The technology behind the Cornelius 10,000 PLUS is equally impressive. It utilizes advanced cooling technology to ensure that beverages are served at the optimal temperature, enhancing the customer experience. The integrated touchless dispensing mechanism minimizes waste and ensures a hygienic experience, addressing growing concerns about cleanliness in food service environments. This technology also improves speed, allowing staff to serve customers more efficiently.

Another key characteristic of the Cornelius 10,000 PLUS is its digital integration capabilities. The system can be connected to a central management platform that tracks sales, inventory levels, and maintenance needs in real-time. This allows operators to optimize their beverage offerings based on customer preferences and reduces downtime through proactive maintenance alerts.

In addition to its performance features, the Cornelius 10,000 PLUS is designed with sustainability in mind. The system employs energy-efficient practices, reducing its environmental footprint while lowering operational costs. The materials used in construction are durable yet eco-friendly, ensuring longevity and less waste.

Overall, the Cornelius 10,000 PLUS stands out as an essential tool for any business looking to elevate its beverage service. With its combination of high capacity, cutting-edge technology, and sustainability features, it not only meets the demands of today’s fast-paced service environments but also positions establishments for future growth and success.
Top Page Image Contents