Note: If your Cooling Unit is equipped with a water tank water level float control, close shutoff valve in plain water inlet supply line.

3.Make sure end of water tank drain hose is routed to floor drain, then remove plug from end of hose and allow water to drain from tank.

CAUTION: Never use an ice pick or other instruments to remove ice from evaporator coils. Such practice can result in punctured refrigeration circuit.

4.Allow ice bank to melt. Hot water may be used to speed melting.

5.Thoroughly rinse inside of water tank with clean water.

6.Install plug in end of water tank drain hose.

Note: If your Cooling Unit is equipped with a water tank water level float control, open shutoff valve in plain water inlet supply line.

7.Fill water tank with clean water until water starts flowing from water tank overflow hose. USE LOW MINERAL CONTENT WATER WHERE A LOCAL WATER PROBLEM EXISTS.

8.Install Cooling Unit top cover and secure with two screws.

9.Connect electrical power to Cooling Unit at disconnect switch.

DOUBLE LIQUID CHECK VALVE ASSEMBLIES YEARLY MAINTENANCE (OR AFTER WATER SYSTEM DISRUPTIONS)

(see Figures 2 and 6)

WARNING: The two double liquid check valve assemblies must be inspected and serviced at least once a year under normal circumstances, and after any disruptions (plumbing work, earthquake, etc.) to the water supply system that might cause turbulent (erratic) flow

of water through the system. Fouled liquid check valves could cause CO2 gas to back flow from the carbonated water tank into the water system and create a health hazard in the system.

The two double liquid check valve assemblies are located in plain water lines connected between the plain water cooling coils and the carbonated water tank. Inspect and clean the double liquid check valve assemblies as follows:

1.Disconnect electrical power from Cooling Unit at disconnect switch.

2.Close shutoff valve in plain water inlet supply line.

3.Note pressure setting on carbonator CO2 regulator, then turn regulator adjusting screw to the left (counterclockwise) until regulator gage reads 0-psi.

4.Pull up on carbonator tank relief valve to release CO2 pressure from tank.

5.Remove two screws securing Cooling Unit top cover, then remove cover.

6.Remove double liquid check valve assembly from plain water line connected between plain water cooling coil and carbonated water tank.

7.Remove one check valve from the other, then disassemble each check valve as shown in Figure 6.

19

300614000

Page 22 Page 24
Page 23
Image 23
Cornelius 000 PLUS, 10 installation manual See Figures 2
Page 22 Page 24

000 PLUS, 10 specifications

Cornelius 10,000 PLUS is a pioneering innovation in the beverage dispensing industry, designed to cater to the evolving needs of commercial establishments. This advanced system combines state-of-the-art technology with user-friendly features, making it a standout choice for restaurants, cafes, and bars aiming to enhance their beverage service.

One of the main features of the Cornelius 10,000 PLUS is its impressive capacity. With the ability to dispense a wide variety of beverages, including soft drinks, cocktails, and craft beers, the system supports a large volume of service, perfect for high-demand environments. The modular design allows for easy expansion, enabling businesses to add additional flavors or beverages as needed without major overhauls.

The technology behind the Cornelius 10,000 PLUS is equally impressive. It utilizes advanced cooling technology to ensure that beverages are served at the optimal temperature, enhancing the customer experience. The integrated touchless dispensing mechanism minimizes waste and ensures a hygienic experience, addressing growing concerns about cleanliness in food service environments. This technology also improves speed, allowing staff to serve customers more efficiently.

Another key characteristic of the Cornelius 10,000 PLUS is its digital integration capabilities. The system can be connected to a central management platform that tracks sales, inventory levels, and maintenance needs in real-time. This allows operators to optimize their beverage offerings based on customer preferences and reduces downtime through proactive maintenance alerts.

In addition to its performance features, the Cornelius 10,000 PLUS is designed with sustainability in mind. The system employs energy-efficient practices, reducing its environmental footprint while lowering operational costs. The materials used in construction are durable yet eco-friendly, ensuring longevity and less waste.

Overall, the Cornelius 10,000 PLUS stands out as an essential tool for any business looking to elevate its beverage service. With its combination of high capacity, cutting-edge technology, and sustainability features, it not only meets the demands of today’s fast-paced service environments but also positions establishments for future growth and success.
Top Page Image Contents