8.Wipe each part with clean lint-free cloth. Inspect each part, especially the ball, for burrs, nicks, corrosion, deterioration, and other damage. Discard ball seat and any damaged or suspicious parts and replace with new parts during reassemble.

9.Reassemble check valves as shown in Figure 6. ALWAYS install new ball seat (QUAD RING) (P/N 312418-000.

NOTE: Make sure when assembling check valves together, check valve female end with white tapered gasket inside, is on inlet side of double liquid check valve assembly.

10.Assemble check valves together. DO NOT OVERTIGHTEN.

11.Install double liquid check valve assembly in plain water line connected between plain water cooling coil and carbonated water tank.

12.Repeat preceding steps 6 through 11 to service other double liquid check valve in other plain water line connected between plain water cooling coil and carbonated water tank.

13.Turn carbonator CO2 regulator adjusting screw to the right (clockwise) until its gage indicates pressure setting observed in step 3 preceding.

14.Open shutoff valve in plain water inlet supply line.

15.Restore electrical power to Cooling Unit at disconnect switch.

16.Dispense carbonated water at dispensing station and allow carbonator to cycle on and off. Check for water leaks and repair if evident.

17.Disconnect electrical power from Cooling Unit at disconnect switch.

18.Install Unit top cover and secure with two screws.

19.Restore electrical power to Cooling Unit at disconnect switch.

LUBRICATION

The carbonator water pump and the carbonated water circulating pump motor bearings must be oiled periodically, refer to oiling instructions on the motors. DO NOT OVER OIL.

ADJUSTMENTS

NOTE: To readjust CO2 regulator to a lower setting loosen adjusting screw lock nut, then turn screw to the left (counterclockwise) until pressure gage reads 5-psi lower than new setting will be. Turn adjusting screw to the right (clockwise) until gage registers new setting, then tighten lock nut.

PRIMARY CO2 REGULATOR

(see Figure 2).

Adjust primary CO2 regulator on CO2 cylinder to a minimum nominal setting of 120-psi or 24-psi higher than highest setting required by the secondary CO2 regulators. Loosen CO2 regulator adjusting screw locknut. Turn adjusting screw to the right (clockwise) until regulator gage registers nominal 120-psi, then tighten adjusting screw locknut.

SECONDARY CO2 REGULATORS

(see Figure 2).

Carbonator Secondary CO2 Regulator.

Adjust carbonator secondary CO2 regulator to a nominal 90-psi. Loosen CO2 regulator adjusting screw locknut. Turn adjusting screw to the right (clockwise) until regulator gage registers nominal 90-psi, then tighten adjusting screw locknut. CO2 PRESSURE TO CARBONATORS MUST NOT EXCEED 125-PSIG.

21

300614000

Page 24 Page 26
Page 25
Image 25
Cornelius 000 PLUS, 10 installation manual Lubrication, Primary CO2 Regulator, Secondary CO2 Regulators
Page 24 Page 26

000 PLUS, 10 specifications

Cornelius 10,000 PLUS is a pioneering innovation in the beverage dispensing industry, designed to cater to the evolving needs of commercial establishments. This advanced system combines state-of-the-art technology with user-friendly features, making it a standout choice for restaurants, cafes, and bars aiming to enhance their beverage service.

One of the main features of the Cornelius 10,000 PLUS is its impressive capacity. With the ability to dispense a wide variety of beverages, including soft drinks, cocktails, and craft beers, the system supports a large volume of service, perfect for high-demand environments. The modular design allows for easy expansion, enabling businesses to add additional flavors or beverages as needed without major overhauls.

The technology behind the Cornelius 10,000 PLUS is equally impressive. It utilizes advanced cooling technology to ensure that beverages are served at the optimal temperature, enhancing the customer experience. The integrated touchless dispensing mechanism minimizes waste and ensures a hygienic experience, addressing growing concerns about cleanliness in food service environments. This technology also improves speed, allowing staff to serve customers more efficiently.

Another key characteristic of the Cornelius 10,000 PLUS is its digital integration capabilities. The system can be connected to a central management platform that tracks sales, inventory levels, and maintenance needs in real-time. This allows operators to optimize their beverage offerings based on customer preferences and reduces downtime through proactive maintenance alerts.

In addition to its performance features, the Cornelius 10,000 PLUS is designed with sustainability in mind. The system employs energy-efficient practices, reducing its environmental footprint while lowering operational costs. The materials used in construction are durable yet eco-friendly, ensuring longevity and less waste.

Overall, the Cornelius 10,000 PLUS stands out as an essential tool for any business looking to elevate its beverage service. With its combination of high capacity, cutting-edge technology, and sustainability features, it not only meets the demands of today’s fast-paced service environments but also positions establishments for future growth and success.
Top Page Image Contents