CyberData 11111, 11113

Operations Guide 930500E CyberData Corporation

Installing the VoIP V3 Indoor Intercom

Configure the Autoprovisioning Parameters

2.4.12 Configure the Autoprovisioning Parameters

1. Click the Autoprovisioning button to open the Autoprovisioning Configuration page. 

See Figure 2-27.

Figure 2-27. Autoprovisioning Configuration Page

Contents

Main Page Important Safety Instructions Warnin g Electrical Hazard: Warnin g Electrical Hazard: Pictorial Alert Icons Hazard Levels General Alert Ground Page Contents Chapter 1 Product Overview 1 Chapter 2 Installing the VoIP V3 Indoor Intercom 9 Appendix A Mounting the Indoor Intercom 65 Appendix B Setting up a TFTP Server 71 Appendix C Troubleshooting/Technical Support 72 Index 76 011211A / 021078C 1.2 Typical System Installation 1.3 Product Features 1.4 Supported Protocols 1.5 Supported SIP Servers 1.6 Product Specifications Table 1-1. Specifications Category Specification a.This number replaces the 011111 number. 1.7 Dimensions Page Figure 1-6. PCB Dimensions and Intrusion Sensor Range Eective Range for Intrusion Sensor to Function from 3 mm to 14 mm 2 Installing the VoIP V3 Indoor Intercom 2.1 Parts List 2.2 Intercom Components 2.2.1 Call Button and the Call Button LED 2.2.1.1 Calling with the The Call Button 2.2.1.2 Call Button LED Function 2.3 Intercom Setup 2.3.1 Intercom Connections J3 Terminal Block Wire (IN) Terminal Block can accept 16 AWG wire 2.3.2 Connecting the Intercom to the Auxiliary Relay Figure 2-4. Auxiliary Relay Wiring Diagram + - Auxiliary Relay Wiring Contacts Controlled Device Such As Electric Door Strike or Strobe Light ( ) Example of External Relay (not supplied) Page Page 2.3.4 Network Connectivity, and Data Rate Link Activity Page 2.3.5 RTFM Button 2.3.5.1 Announcing the IP Address 2.3.5.2 Restoring the Factory Default Settings 2.3.6 Adjust the Volume 2.4 Configure the Intercom Parameters 2.4.1 Factory Default Settings a. Default if there is not a DHCP server present. 2.4.2 Intercom Web Page Navigation Tabl e 2-5 shows the navigation buttons that you will see on every Intercom web page. Table 2-5. Web Page Navigation 2.4.3 Log in to the Configuration Home Page Page 3. On the Home Page, review the setup details and navigation buttons described in Table 2-6. Table 2-6. Home Page Overview Page Page 3. After changing the parameters, click the Save button. Table 2-7. Device Configuration Parameters (continued) Page Page Page Page 2.4.6.1 Dial Out Extension Strings and DTMF Tones (using rfc2833) 2.4.6.2 Point-to-Point Configuration 2.4.6.3 Delayed DTMF 2.4.7 Configure the Nightringer Parameters Table 2-12. Nightringer Configuration Parameters 3. After changing the parameters, click on the Save button. 2.4.8 Configure the Sensor Configuration Parameters Page 2. On the Sensor Configuration page, enter values for the parameters indicated in Table 2-13. 3. After changing the parameters, click Save Settings. Table 2-13. Sensor Configuration Parameters 2.4.9 Configure the Multicast Parameters 2.4.9.1 Assigning Priority Page Page Table 2-15. Audio Configuration Parameters 2.4.10.1 User-created Audio Files Page 2.4.11 Configure the Event Parameters Table 2-16. Event Configuration 2.4.11.1 Example Packets for Events Page Page Page Page 2.4.12.1 Autoprovisioning Page Page 2.5 Upgrade the Firmware and Reboot the Intercom 2.5.1 Uploading the Firmware Equipment Hazard: Page 2.5.2 Reboot the Intercom 2.6 Command Interface 2.6.1 Command Interface Post Commands Page Page Page Appendix A: Mounting the Indoor Intercom A.1 Wall Mounting Components A.2 Cable Connections Figure A-1 shows how to properly connect the VoIP Intercom. Figure A-1. Cable Connections J2 J7 J6 A.3 Wall Mounting Option Figure A-2 shows a wall mounting option. Figure A-2. Wall Mounting Option A.4 Wall Cutout Dimensions Mounting the Indoor Intercom Gang Box Option Operations Guide 930500E CyberData Corporation 69 A.5 Gang Box Option Figure A-4 shows a 1-Gang Box and a 2-Gang Box mounting option. Figure A-4. Gang Box Mounting A.6 PCB Dimensions Eective Range for Intrusion Sensor to Function from 3 mm to 14 mm Appendix B: Setting up a TFTP Server B.1 Set up a TFTP Server B.1.1 In a LINUX Environment B.1.2 In a Windows Environment Appendix C: Troubleshooting/Technical Support C.1 Frequently Asked Questions (FAQ) C.2 Documentation C.3 Contact Information C.4 Warranty C.4.1 Warranty & RMA Returns within the United States C.4.2 Warranty & RMA Returns Outside of the United States C.4.3 Spare in the Air Policy Page Index Numerics A B C E F G H I N O P R S T U V W Y