CY8C24123A
CY8C24223A, CY8C24423A
Document Number: 38-12028 Rev. *I Page 22 of 56
DC Operational Amplifier Specifications
The following tables list the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters
apply to 5V, 3.3V, and 2.7V at 25°C and are for design guidance only.
The Operational Amplifier is a component of both the Analog Continuous Time PSoC blocks and the Analog Switched Cap PSoC
blocks. The guaranteed specifications are measured in the Analog Continuous Time PSoC block. Typical parameters apply to 5V at
25°C and are for design guidance only.
Table 17. 5V DC Operational Amplifier Specifications
Symbol Description Min Typ Max Units Notes
VOSOA Input Offset Voltage (absolute value)
Power = Low, Opamp Bias = High
Power = Medium, Opamp Bias = High
Power = High, Opamp Bias = High
–1.6
1.3
1.2
10
8
7.5
mV
mV
mV
–
–
TCVOSOA Average Input Offset Voltage Drift – 7.0 35.0 μV/°C
IEBOA Input Leakage Current (Port 0 Analog Pins) – 20 – pA Gross tested to 1 μA
CINOA Input Capacitance (Port 0 Analog Pins) – 4.5 9.5 pF Package and pin dependent.
Temp = 25°C
VCMOA Common Mode Voltage Range
Common Mode Voltage Range (high power or
high opamp bias)
0.0 – Vdd
Vdd - 0.5 V The common-mode input voltage
range is measured through an
analog output buffer. The
specification includes the
limitations imposed by the
characteristics of the analog
output buffer.
0.5 –
GOLOA Open Loop Gain
Power = Low, Opamp Bias = High
Power = Medium, Opamp Bias = High
Power = High, Opamp Bias = High
60
60
80
– – dB Specification is applicable at high
power. For all other bias modes
(except high power, high opamp
bias), minimum is 60 dB.
VOHIGHOA High Output Voltage Swing (internal signals)
Power = Low, Opamp Bias = High
Power = Medium, Opamp Bias = High
Power = High, Opamp Bias = High
Vdd - 0.2
Vdd - 0.2
Vdd - 0.5
–
–
–
–
–
–
V
V
V
VOLOWOA Low Output Voltage Swing (internal signals)
Power = Low, Opamp Bias = High
Power = Medium, Opamp Bias = High
Power = High, Opamp Bias = High
–
–
–
–
–
–
0.2
0.2
0.5
V
V
V
ISOA Supply Current (including associated AGND
buffer)
Power = Low, Opamp Bias = High
Power = Low, Opamp Bias = High
Power = Medium, Opamp Bias = High
Power = Medium, Opamp Bias = High
Power = High, Opamp Bias = High
Power = High, Opamp Bias = High
–
–
–
–
–
–
150
300
600
1200
2400
4600
200
400
800
1600
3200
6400
μA
μA
μA
μA
μA
μA
PSRROA Supply Voltage Rejection Ratio 64 80 – dB Vss ≤ VIN ≤ (Vdd - 2.25) or
(Vdd - 1.25V) ≤ VIN ≤ Vdd
[+] Feedback