Configure WPA Radius | D-Link DIR-455 guide

Section 4 - Security

Configure WPA (RADIUS)

It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead.

1.Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). Click on Wireless Settings on the left side.

2.Next to Security Mode, select Enable WPA-Personal Security or Enable WPA2-Personal Security.

3.Next to Cipher Mode, select TKIP, AES, or Auto.

4.Next to PSK/EAP, select EAP.

5.Next to RADIUS Server 1 enter the IP Address of your RADIUS server.

6.Next to Port, enter the port you are using with your RADIUS server. 1812 is the default port.

7.Next to Shared Secret, enter the security key.

8.If you have a secondary RADIUS server, enter its IP address, port, and secret key.

9.Click Apply Settings to save your settings.

D-Link DIR-455 User Manual

70

Image 74

D-Link DIR-455 manual Configure WPA Radius

Contents

Page Preface Trademarks Table of Contents Troubleshooting Wireless Basics ProductPackageOverviewContents Introduction Rear Panel PowerHardware Overview LAN4 LAN3 LAN2 LAN1 WAN SIM WPS Front PanelWAN LAN1 LAN2 LAN3 LAN4 SMS Wlan LEDs WAN Installation Connect to Your Network Connect a Telephone Wireless Installation Considerations Configuration Web-based Configuration Utility Click Internet Connection Setup Wizard to begin Setup WizardInternet Connection Setup Wizard Manual Internet Connection Setup and skip toPage Page Page Manual Internet Connection Setup Click Manual Internet Connection Setup to begin Internet Connection Internet Connection Type Dynamic IP Dhcp PPPoE Pptp IP Address Address ModeReconnect Mode Pptp Subnet Mask L2TP IP Address L2TP Subnet Mask Keep Alive AuthenticationDialed Number Static IP GRE Settings GRE Tunnel Tunnels Information Mode Wireless SettingsWireless Network Settings Wireless Security Mode Network Settings Router Settings Dhcp Lease Time Dhcp Server SettingsEnable Dhcp Server Secondary Wins IP Address VPN Settings Page Tunnel 1 IKE Encapsulation Protocol ESP, AH, or ESP+AHPage Page IKE Proposal Settings Ipsec Proposal Settings Tunnel 1 Manual Key Page Encapsulation Protocol ESP, AH, or ESP+AH Preshared Key XAuth Server ModePFS Group Remote ID IKE Proposal Settings Create Message Message ServiceSMS Inbox Inbox CancelReceiver Refresh Copy to EnableVirtual Server Virtual Servers List Application Rules Application Rules Local IP Ports QoS EngineQOS Packet Filter QoS Priority MAC Filtering Rules MAC Filtering SettingsMAC Address Filter URL Filter URL Filtering Rules Outbound Filter Rules List Outbound Filter SettingOutbound Filter Inbound Filter Rules List Intbound Filter SettingInbound Filter Snmp Set Community Routing Rules RIP SettingRouting Advanced Wireless Dtim Interval WMM Capable TX Rates WAN Ping Advanced NetworkUpnp Remote Management AdminAdministrator Time Zone ConfigurationTime Set the Time and Date Syslog Mail Settings System Firmware Dynamic DNS Username / E-mail Enter the Username for your System Check Schedules Device Information Logs Statistics Wireless Support Wireless Security What is WEP? Configure WEP Next to Security Mode, select Enable WEP Security What is WPA? Configure WPA-PSK Configure WPA Radius Connect to a Wireless Network Using Windows Vista Configure Wireless Security Page Using Windows XP Configure WEP Page Configure WPA-PSK Page Troubleshooting Why can’t I access the web-based configuration utility? What can I do if I forgot my password? Wireless Basics Wireless Local Area Network Wlan Wireless Personal Area Network Wpan Home Small Office and Home Office Security Centralize your Router or Access PointEliminate Interference Wireless Modes Networking Basics Check your IP address Statically Assign an IP address Step Technical Specifications GSM Band GSM/GPRS/EDGE Dimensions L x W x H