Manuals / Datamax / Computer Equipment / Printer

Datamax E-4304e, E-4203, E-4204 Font 4 62-character, Font 5 62-character, alphanumeric, uppercase

Models: E-4204 E-4203 E-4304e

1 92

Download 92 pages 61.43 Kb

Page 71

Font 4 62-character

Font 4 62-character	Font 5 62-character
alphanumeric, uppercase.	alphanumeric, uppercase.

Font 6 62-character alphanumeric, uppercase.

E-4203/E-4204/E-4304

61

Image 71

Datamax E-4304e manual Font 4 62-character, Font 5 62-character, alphanumeric, uppercase, E-4203/E-4204/E-4304

Contents

w/USB Operator’s ManualE-4203 / E-4204 / E-4304 Page Firmware Software Agreement Copyright InformationEN60950 Agency Compliance and ApprovalsC22.2 No. 950-M93 C US ListedImportant Safety Instructions Page Getting Started Setting Up the PrinterUsing the Front Panel Printer OverviewSpecifications Maintenance and AdjustmentsTroubleshooting ASCII Control Code Chart Appendix AAppendix B Appendix CPage Thermal Transfer Model 1.0 IntroductionDirect Thermal Model Memory 1.1.1 Standard Features1.1 About this Printer PrintingExternal Media Supply Stand 1.1.2 Optional FeaturesAdjustable Media Sensor Heavy Duty Power SupplyThermal Transfer Present SensorRemoving the Packaging 2.0 Before Using the PrinterAdditional Requirements Inspecting the Printer3.0 Introduction 3.1 Connecting the Printer3.1.1 Power Connection 3.1.3 Interface Cables 3.1.2 Interface Connection3.2 Adjusting the Media Sensor TOF Sensing Used Adjustable Media Sensor PositionSuggested Sensor Placement Media Typeinches ReferenceDistance of the TOF Mark Distance from the Media Edge Letter3.3 Loading Media 5. Slide the Media Guide and Media Hub Flange to the edge of the media 3.3.1 Loading Media for Peel Configuration 3.4 Loading Ribbon 6. Place the Ribbon Hubs back into the printer and route the ribbon through the Printhead Carrier Assembly, as shown below 3.5 Flash Memory Expansion E-4203/E-4204/E-4304 E-4203/E-4204/E-4304 4.0 Introduction4.1 Lights Button Combinations push buttons simultaneously 4.2 Buttons4.3 Normal Mode - Button Functions To change Printer Setup 4.4 Printer Setup Mode - Button FunctionsMenu 4.4.1 Printer Setup Menu ListMenu Item Values1 MEDIA TYPE 4.4.2 Menu Items and Values5 SOP ADJUST 6 PRESENT ADJUST9 CONTROL CODES 21 INPUT MODE 19 ALIGN LENGTH20 STOP LOCATION Yes see Section4.4.3 Step by Step Modification of the Printer Setup E-4203/E-4204/E-4304 The new 19200 Baud Rate4.5.1 Label Alignment = YES 4.5 Label AlignmentAuto Alignment with the Present Sensor enabled 4.5.2 Label Alignment = AUTO4.5.3 Label Alignment = NO Possible Cause 4.5.4 Label Alignment TroubleshootingProblem SolutionPossible Cause ProblemSolution Possible Cause ProblemSolution Possible Cause ProblemSolution To perform Calibration 4.6 Calibration Mode - Button Functions4.6.1 Auto Media Sensor Calibration 4.6.2 Manual Media Sensor Calibration To print the Database Configuration and Dot Check Labels 4.7.1 Database Configuration and Dot Check Labels4.7 Internal Labels Good Dot Check Label Faulty Dot Check LabelTo print the Test Label 4.7.2 Test Label4.7.3 Hex Dump Label To exit the Hex Dump Mode To print the Hex Dump LabelInterval 5.0 IntroductionArea Method5.1 Cleaning the Printhead 5.2 Media Width Adjustment 5.3 Ribbon Width Adjustment 5.4 Fine Printhead Adjustment Removal 5.5 Printhead ReplacementReplacement copy filename.dlf lpt1/b 5.6 Darkness Adjustment5.7 Resetting to the Factory Defaults 5.8 Downloading Firmware and Fonts3. The PAUSED Light will flash during the download Page 6.1 Troubleshooting Tips6.0 Introduction Problem SituationThe ribbon does not advance Unacceptable print qualityThe printer does not print or prints several labels at once Prints light on the right side of the label Printer fails to power onSkips every other label Unable to print in rotationTracking Problems Label advances 1-2 inches before a fault indicationLabel advances 16 inches before a fault indication E-4203 MechanicalPrinting optional power supplyEmbedded Bar Codes Media/RibbonCommunications FontsMaximum1 Approved MediaDesignator DescriptionE-4203/E-4204/E-4304 E-4203/E-4204/E-4304 ASCII Control Code ChartCtrl S DC3 Notes For the hardware handshake XON/XOFF commandsCtrl Q DC1 XOFFProgrammers Manual Embedded Fonts and BarcodesDependent upon selected symbol set see the Fontscase Font 0 96-character alphanumeric, upper and lower caseFont 2 138-character alphanumeric, upper and lowerFont 6 62-character alphanumeric, uppercase Font 4 62-characterFont 5 62-character alphanumeric, uppercasePoint sizes are selected by the number in the barcode height Font 7 OCR-A, sizeFont 8 OCR-B, size Font 9 Internal Triumvirate fontLength BarcodesBar Code TypeCheck Bar CodeType LengthBarcode E Code Barcode A Code 3 ofBarcode C UPC-E Barcode D Interleaved 2 ofBarcode K Plessey Barcode I CodabarBarcode J Interleaved 2 of w/module 10 checksumE-4203/E-4204/E-4304 Barcode S UCC/EAN Code 128 Random WeightBarcode Q UCC/EAN Code 128 Barcode R UCC/EAN Code KMART NON EDI Bar Code W1c DataMatrix Barcode T TelepenBarcode u UPS MaxiCode Barcode z PDF417 Barcode v FIME-Class 4203/4204/4304 Printer Datamax Barcode Products Limited Warranty StatementPrinter Thermal Printhead Warranty Service ProceduresLimitation of Liability General Warranty ProvisionsE-4203/E-4204/E-4304 Glossary diagnostics Programs used to locate and diagnose hardware problems font A set of alphanumeric characters that share a particular typeface registration Repeatable top to bottom alignment of printed labels void An undesirable blank space in a printed image E-4203/E-4204/E-4304 Index Page Page E-4203/E-4204/E-4304