Manuals / Datamax / Computer Equipment / Printer

Datamax E-4203, E-4204 Barcode T Telepen, Barcode u UPS MaxiCode, Barcode z PDF417 Barcode v FIM

Models: E-4204 E-4203 E-4304e

1 92

Download 92 pages 61.43 Kb

Page 78

Barcode T Telepen

Barcode T Telepen

Barcode u UPS MaxiCode

Barcode z PDF417

Barcode v FIM

Bar Code W1c: DataMatrix

Bar Code W1d: QR Code

Bar Code W1f: Aztec	Bar Code W1z: MicroPDF417

Bar Code W1T: TCIF Linked Barcode 3 of 9 (TLC39)

68	E-4203/E-4204/E-4304

Image 78

Datamax E-4203, E-4204 Barcode T Telepen, Barcode u UPS MaxiCode, Barcode z PDF417 Barcode v FIM, Bar Code W1c DataMatrix

Contents

Operator’s Manual E-4203 / E-4204 / E-4304w/USB Page Copyright Information Firmware Software AgreementC US Listed Agency Compliance and ApprovalsC22.2 No. 950-M93 EN60950Important Safety Instructions Page Printer Overview Setting Up the PrinterUsing the Front Panel Getting StartedMaintenance and Adjustments TroubleshootingSpecifications Appendix C Appendix AAppendix B ASCII Control Code ChartPage 1.0 Introduction Direct Thermal ModelThermal Transfer Model Printing 1.1.1 Standard Features1.1 About this Printer MemoryHeavy Duty Power Supply 1.1.2 Optional FeaturesAdjustable Media Sensor External Media Supply StandPresent Sensor Thermal Transfer2.0 Before Using the Printer Removing the PackagingInspecting the Printer Additional Requirements3.1 Connecting the Printer 3.1.1 Power Connection3.0 Introduction 3.1.2 Interface Connection 3.1.3 Interface Cables3.2 Adjusting the Media Sensor Media Type Adjustable Media Sensor PositionSuggested Sensor Placement TOF Sensing UsedLetter ReferenceDistance of the TOF Mark Distance from the Media Edge inches3.3 Loading Media 5. Slide the Media Guide and Media Hub Flange to the edge of the media 3.3.1 Loading Media for Peel Configuration 3.4 Loading Ribbon 6. Place the Ribbon Hubs back into the printer and route the ribbon through the Printhead Carrier Assembly, as shown below 3.5 Flash Memory Expansion E-4203/E-4204/E-4304 4.0 Introduction 4.1 LightsE-4203/E-4204/E-4304 4.3 Normal Mode - Button Functions 4.2 ButtonsButton Combinations push buttons simultaneously 4.4 Printer Setup Mode - Button Functions To change Printer SetupValues 4.4.1 Printer Setup Menu ListMenu Item Menu6 PRESENT ADJUST 4.4.2 Menu Items and Values5 SOP ADJUST 1 MEDIA TYPE9 CONTROL CODES 20 STOP LOCATION 21 INPUT MODE19 ALIGN LENGTH Yes see Section4.4.3 Step by Step Modification of the Printer Setup The new 19200 Baud Rate E-4203/E-4204/E-43044.5 Label Alignment 4.5.1 Label Alignment = YES4.5.2 Label Alignment = AUTO 4.5.3 Label Alignment = NOAuto Alignment with the Present Sensor enabled Solution 4.5.4 Label Alignment TroubleshootingProblem Possible CauseProblem SolutionPossible Cause Problem SolutionPossible Cause Problem SolutionPossible Cause 4.6 Calibration Mode - Button Functions To perform Calibration4.6.1 Auto Media Sensor Calibration 4.6.2 Manual Media Sensor Calibration 4.7.1 Database Configuration and Dot Check Labels 4.7 Internal LabelsTo print the Database Configuration and Dot Check Labels Faulty Dot Check Label Good Dot Check Label4.7.2 Test Label 4.7.3 Hex Dump LabelTo print the Test Label To exit the Hex Dump Mode To print the Hex Dump LabelMethod 5.0 IntroductionArea Interval5.1 Cleaning the Printhead 5.2 Media Width Adjustment 5.3 Ribbon Width Adjustment 5.4 Fine Printhead Adjustment 5.5 Printhead Replacement ReplacementRemoval 5.8 Downloading Firmware and Fonts 5.6 Darkness Adjustment5.7 Resetting to the Factory Defaults copy filename.dlf lpt1/b3. The PAUSED Light will flash during the download Problem Situation 6.1 Troubleshooting Tips6.0 Introduction PageUnacceptable print quality The printer does not print or prints several labels at onceThe ribbon does not advance Unable to print in rotation Printer fails to power onSkips every other label Prints light on the right side of the labelLabel advances 1-2 inches before a fault indication Label advances 16 inches before a fault indicationTracking Problems optional power supply MechanicalPrinting E-4203Fonts Media/RibbonCommunications Embedded Bar CodesDescription Approved MediaDesignator Maximum1E-4203/E-4204/E-4304 ASCII Control Code Chart E-4203/E-4204/E-4304XOFF Notes For the hardware handshake XON/XOFF commandsCtrl Q DC1 Ctrl S DC3Fonts Embedded Fonts and BarcodesDependent upon selected symbol set see the Programmers Manualalphanumeric, upper and lower Font 0 96-character alphanumeric, upper and lower caseFont 2 138-character casealphanumeric, uppercase Font 4 62-characterFont 5 62-character Font 6 62-character alphanumeric, uppercaseFont 9 Internal Triumvirate font Font 7 OCR-A, sizeFont 8 OCR-B, size Point sizes are selected by the number in the barcode heightType BarcodesBar Code LengthLength Bar CodeType CheckBarcode D Interleaved 2 of Barcode A Code 3 ofBarcode C UPC-E Barcode E Codew/module 10 checksum Barcode I CodabarBarcode J Interleaved 2 of Barcode K PlesseyBarcode S UCC/EAN Code 128 Random Weight Barcode Q UCC/EAN Code 128 Barcode R UCC/EAN Code KMART NON EDIE-4203/E-4204/E-4304 Barcode z PDF417 Barcode v FIM Barcode T TelepenBarcode u UPS MaxiCode Bar Code W1c DataMatrixDatamax Barcode Products Limited Warranty Statement PrinterE-Class 4203/4204/4304 Printer Warranty Service Procedures Thermal PrintheadGeneral Warranty Provisions Limitation of LiabilityE-4203/E-4204/E-4304 Glossary diagnostics Programs used to locate and diagnose hardware problems font A set of alphanumeric characters that share a particular typeface registration Repeatable top to bottom alignment of printed labels void An undesirable blank space in a printed image E-4203/E-4204/E-4304 Index Page Page E-4203/E-4204/E-4304