Manuals / Datamax / Computer Equipment / Printer

Datamax E-4203 Appendix A, Appendix B, Appendix C, ASCII Control Code Chart, Warranty Information

Models: E-4204 E-4203 E-4304e

1 92

Download 92 pages 61.43 Kb

Page 9

Appendix A
ASCII Control Code Chart	57
Appendix B
Embedded Fonts and Barcodes	59
Appendix C
Warranty Information	69
Glossary	73
Index	79

iii

Image 9

Datamax E-4203 Appendix A, Appendix B, Appendix C, ASCII Control Code Chart, Embedded Fonts and Barcodes, Glossary, Index

Contents

Operator’s Manual E-4203 / E-4204 / E-4304w/USB Page Firmware Software Agreement Copyright InformationC22.2 No. 950-M93 Agency Compliance and ApprovalsC US Listed EN60950Important Safety Instructions Page Using the Front Panel Setting Up the PrinterPrinter Overview Getting StartedMaintenance and Adjustments TroubleshootingSpecifications Appendix B Appendix AAppendix C ASCII Control Code ChartPage 1.0 Introduction Direct Thermal ModelThermal Transfer Model 1.1 About this Printer 1.1.1 Standard FeaturesPrinting MemoryAdjustable Media Sensor 1.1.2 Optional FeaturesHeavy Duty Power Supply External Media Supply StandThermal Transfer Present SensorRemoving the Packaging 2.0 Before Using the PrinterAdditional Requirements Inspecting the Printer3.1 Connecting the Printer 3.1.1 Power Connection3.0 Introduction 3.1.3 Interface Cables 3.1.2 Interface Connection3.2 Adjusting the Media Sensor Suggested Sensor Placement Adjustable Media Sensor PositionMedia Type TOF Sensing UsedDistance of the TOF Mark Distance from the Media Edge ReferenceLetter inches3.3 Loading Media 5. Slide the Media Guide and Media Hub Flange to the edge of the media 3.3.1 Loading Media for Peel Configuration 3.4 Loading Ribbon 6. Place the Ribbon Hubs back into the printer and route the ribbon through the Printhead Carrier Assembly, as shown below 3.5 Flash Memory Expansion E-4203/E-4204/E-4304 4.0 Introduction 4.1 LightsE-4203/E-4204/E-4304 4.3 Normal Mode - Button Functions 4.2 ButtonsButton Combinations push buttons simultaneously To change Printer Setup 4.4 Printer Setup Mode - Button FunctionsMenu Item 4.4.1 Printer Setup Menu ListValues Menu5 SOP ADJUST 4.4.2 Menu Items and Values6 PRESENT ADJUST 1 MEDIA TYPE9 CONTROL CODES 19 ALIGN LENGTH 21 INPUT MODE20 STOP LOCATION Yes see Section4.4.3 Step by Step Modification of the Printer Setup E-4203/E-4204/E-4304 The new 19200 Baud Rate4.5.1 Label Alignment = YES 4.5 Label Alignment4.5.2 Label Alignment = AUTO 4.5.3 Label Alignment = NOAuto Alignment with the Present Sensor enabled Problem 4.5.4 Label Alignment TroubleshootingSolution Possible CauseProblem SolutionPossible Cause Problem SolutionPossible Cause Problem SolutionPossible Cause To perform Calibration 4.6 Calibration Mode - Button Functions4.6.1 Auto Media Sensor Calibration 4.6.2 Manual Media Sensor Calibration 4.7.1 Database Configuration and Dot Check Labels 4.7 Internal LabelsTo print the Database Configuration and Dot Check Labels Good Dot Check Label Faulty Dot Check Label4.7.2 Test Label 4.7.3 Hex Dump LabelTo print the Test Label To print the Hex Dump Label To exit the Hex Dump ModeArea 5.0 IntroductionMethod Interval5.1 Cleaning the Printhead 5.2 Media Width Adjustment 5.3 Ribbon Width Adjustment 5.4 Fine Printhead Adjustment 5.5 Printhead Replacement ReplacementRemoval 5.7 Resetting to the Factory Defaults 5.6 Darkness Adjustment5.8 Downloading Firmware and Fonts copy filename.dlf lpt1/b3. The PAUSED Light will flash during the download 6.0 Introduction 6.1 Troubleshooting TipsProblem Situation PageUnacceptable print quality The printer does not print or prints several labels at onceThe ribbon does not advance Skips every other label Printer fails to power onUnable to print in rotation Prints light on the right side of the labelLabel advances 1-2 inches before a fault indication Label advances 16 inches before a fault indicationTracking Problems Printing Mechanicaloptional power supply E-4203Communications Media/RibbonFonts Embedded Bar CodesDesignator Approved MediaDescription Maximum1E-4203/E-4204/E-4304 E-4203/E-4204/E-4304 ASCII Control Code ChartCtrl Q DC1 Notes For the hardware handshake XON/XOFF commandsXOFF Ctrl S DC3Dependent upon selected symbol set see the Embedded Fonts and BarcodesFonts Programmers ManualFont 2 138-character Font 0 96-character alphanumeric, upper and lower casealphanumeric, upper and lower caseFont 5 62-character Font 4 62-characteralphanumeric, uppercase Font 6 62-character alphanumeric, uppercaseFont 8 OCR-B, size Font 7 OCR-A, sizeFont 9 Internal Triumvirate font Point sizes are selected by the number in the barcode heightBar Code BarcodesType LengthType Bar CodeLength CheckBarcode C UPC-E Barcode A Code 3 ofBarcode D Interleaved 2 of Barcode E CodeBarcode J Interleaved 2 of Barcode I Codabarw/module 10 checksum Barcode K PlesseyBarcode S UCC/EAN Code 128 Random Weight Barcode Q UCC/EAN Code 128 Barcode R UCC/EAN Code KMART NON EDIE-4203/E-4204/E-4304 Barcode u UPS MaxiCode Barcode T TelepenBarcode z PDF417 Barcode v FIM Bar Code W1c DataMatrixDatamax Barcode Products Limited Warranty Statement PrinterE-Class 4203/4204/4304 Printer Thermal Printhead Warranty Service ProceduresLimitation of Liability General Warranty ProvisionsE-4203/E-4204/E-4304 Glossary diagnostics Programs used to locate and diagnose hardware problems font A set of alphanumeric characters that share a particular typeface registration Repeatable top to bottom alignment of printed labels void An undesirable blank space in a printed image E-4203/E-4204/E-4304 Index Page Page E-4203/E-4204/E-4304