Installation | Dell 2700W manual

4For models with a detachable power cord. Plug the detachable UPS power cord into the input connector on the UPS rear panel.

5Plug the UPS power cord into a power outlet.

The UPS front panel display illuminates. The Dell startup screen changes to the UPS status summary screen. The UPS front panel display shows the flashing Standby icon .

6Press the button on the UPS front panel.

After the startup is complete, the status icon changes to the appropriate icon based on the UPS operating mode (see Table 4 on page 36).

7On the UPS status summary screen, press the button to check for active alarms or notices. Resolve any active alarms before continuing. See “Troubleshooting” on page 66.

If there are no active alarms, a “No Active Alarms” message appears.

8Verify that the Normal icon appears on the UPS status summary screen, indicating that the UPS is operating normally and any loads are powered (see Table 4 on page 36).

9If an optional EBM is installed, see “Configuring the UPS for an EBM” on page 52.

10To change other factory-set defaults, see “Operation” on page 31.

11If you installed an optional REPO, test the REPO function:

Activate the external REPO switch. Verify the status change on the UPS display.

Deactivate the external REPO switch and restart the UPS.

NOTE: Dell recommends setting the date and time.

NOTE: At initial startup, the UPS sets system frequency according to input line frequency (input frequency auto-sensing is enabled by default). After initial startup, auto-sensing is disabled until manually re-enabled by output frequency setting.

NOTE: At initial startup, input voltage auto-sensing is enabled by default. After the subsequent startup, auto-sensing is disabled until manually re-enabled by output voltage setting.

NOTE: The internal batteries charge to 90% capacity in less than 4 hours. However, Dell recommends that the batteries charge for 48 hours after installation or long-term storage. If an optional EBM is installed, see the recharge time listed in Table 15 on page 65.

30 Installation

Image 30

Dell 2700W manual Installation

Contents

Users Guide July 2013 S 164201788 Table of Contents RS-232 and USB Communication Ports Dell UPS Management Software Testing Batteries UPS Status Menu Event Log Menu Introduction Dell Online Rack UPS Introduction Finding Information What are You Looking For? Find It Here Safety Warnings UPS Output Power Safety Warnings Do not add weight to slide/rail mounted equipment Installation Inspecting the Equipment Unpacking the Cabinet Unpacking the Cabinet Lifting the Cabinet Identifying the UPS Rear Panels 120V Rear Panel Identifying the UPS Front Panel 230V Rear Panel Rackmount Setup Opening the Metal Battery Cover If installing additional UPSs, repeat for each cabinet Positioning the Rails Attaching the Rails to the Rack Installing and Securing the Cabinet Installing the Battery Tray Install the UPS front cover see Figure Installing the EBM Removing the Battery Connector Cover Installing the Strain Relief Bracket Installing the UPS EBM Installation Installing Remote Emergency Power-off Repo Connections Wire Function Repo Connector Minimum Upstream Circuit Breaker Rating UPS Output Power Power Cord RatingsUPS Initial Startup Installation Operation UPS Startup and ShutdownStarting the UPS Starting the UPS on Battery UPS Shutdown Control Panel Functions Control Button Functions Control Button Sequence Changing the Language Display FunctionsStartup Screen Screen Locked UPS Status Bad Battery Detected or Battery Disconnected Battery ModeBypass Mode UPS General Alarms Active High Efficiency Mode Status Summary Screens Description Battery Test StatusNormal Mode Converter Mode Battery Status Screens Description Event Log Measurements Control Screens Control Screens Description Settings Settings Description Available Settings Default SettingIdentification Settings Description Available Settings Default Setting Settings Description Available Settings Default Setting Settings Description Available Settings Default Setting Settings Description Available Settings Default Setting Transferring from Normal to Bypass Mode Transferring the UPS Between Modes Setting Power Strategy Transferring from Bypass to Normal Mode Retrieving the Event Log Behavior on Overload Configuring Load Segments Controlling Load Segments Through the Display Configuring Automatic Start Delay Configuring Automatic on Battery Shutdown Configuring Battery Settings Configuring the UPS for an EBM Configuring Automatic Restart Running Automatic Battery TestsConfiguring Automatic Battery Tests Additional UPS Features RS-232 and USB Communication Ports RS-232 Communication Port Pin Assignment GND Dell Network Management Card Optional Dell Network Management Card Dell UPS Management Software UPS Maintenance UPS and Battery CareTransporting the UPS Remove the UPS front cover see Figure Disconnect the internal battery connectors see Figure When to Replace Batteries Storing the UPS and Batteries Testing Batteries Updating the UPS Firmware Specifications Regulation Battery mode Power LevelsRated at nominal inputs Regulation Normal mode Environmental and Safety Voltage Battery ConfigurationBattery Runtimes Fuses Troubleshooting Accessing Alarms and ConditionsUPS Status Menu Typical Alarms and Conditions Event Log Menu Action Troubleshooting Troubleshooting Silencing the Alarm