Delta DVPEN01-SL 2 Product Profile & Outline

Ethernet Communication Module DVPEN01-SL

DVP-PLC Operation Manual

Item Specification

Storage: -25°C ~ 70°C (temperature), 5 ~ 95% (humidity)

Vibration/ Shock Resistance Standard: IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea)

 Electrical specifications

Item Specification

Power supply voltage 24VDC (-15% ~ 20%) (Power is supplied by the internal bus of MPU.)

Power consumption 1.5W

Insulation voltage 500V

Weight (g) 92 (g)

2 Product Profile & Outline

2.1 Dimension

LAN

RS-232

LINK

DVPEN01

RS-232

POWER

100M

60 [2.362]

90 [3.543]

3 [0.118]

Unit: mm [inches]

2.2 Product Profiles

LAN

RS-232

LINK

DVPEN01

RS-232

POWER

100M

1. Model name 6. Fixing tenon for I/O module

2. Extension port to connect device 7. Fixing clip for I/O module

3. Extension port to connect I/O module 8. RS-232 connection port

4. POWER, LINK, RS-232, 100M indicators 9. Ethernet RJ-485 connection port

5. DIN rail clip

Contents

Main Ethernet Communication Module Operation Manual Page Ethernet Communication Module DVPEN01-SL Warning Table of Contents Page 1 Introduction 1.1 Functions 1.2 Specifications 2 Product Profile & Outline 2.1 Dimension 90 [3.543] 60 [2.362] 3 Installation & Wiring 3.1 Installation 4 Control Register (CR) 4.1 Control Registers in DVPEN01-SL Page 4.2 Explanations on CR Page Page Page Page 4.3 Numbering of Left-Side Modules 5 Setting up Software 5.1 Setting up Communication & Searching for Modules Page Page Page Page Page 5.2 Basic Settings 5.3 Network Settings Page Page 5.4 Setting up E-Mails 5.5 Data Exchange 5.6 RTU 5.7 IP Filter 5.8 Static ARP Table 5.9 Setting up Password 5.10 Returning to Default Setting 6 Application Examples 6.1 Setting up IP and Communicating through WPLSoft Page Page 6.2 Connecting the PC with DVPEN01-SL through LAN Page Page Page 6.3 Setting up Password and Clearing Password Page 6.4 When the Password is Lost (Returning to Default Setting by RS-232) 6.5 IP Filter Protection Page 6.6 Setting up Static ARP Table Page 6.7 Application of E-Mail If the rising-edge of X0 is triggered, X0 will go from Off to On. Write 1 into CR#3 of If the falling-edge of X0 is triggered, X0 will go from On to Off. Write 1 into CR#4 of If the rising-edge of Y0 is triggered, Y0 will go from Off to On. Write 1 into CR#5 of If the falling-edge of Y0 is triggered, Y0 will go from On to Off. Write 1 into CR#6 of 6.8 Application of Data Exchange (1) Page Page 6.9 Application of Data Exchange (2) 6.10 Application of Data Exchange (3) 6.11 Application of Data Exchange (4) Write the IP address of PLC_A into CR#25 and CR#26. The first two IP codes (192.168 = 6.12 Application of Data Exchange (5) Write 0 into CR#28, and PLC_B will use CR#25 ~ CR#26 as the IP address of the destination Write the IP address of PLC_A into CR#25 and CR#26. The first two IP codes (192.168 = 6.13 Application of Modbus TCP Master Set CR#111 as 1 to enable the 8-bit mode. The Modbus instruction is stored in the low byte of 6.14 RTU Mapping