Set up speakers (Audyssey® Setup)
Error messagesNOTE
•An error message is displayed if Audyssey® Setup could not be completed due to speaker placement, the measurement environment, etc. If an error message is displayed, check the relevant items and perform the necessary measures. Then perform Audyssey® Setup again.
•If the result still differs from the actual connection status after remeasurement or the error message still appears, it is possible that the speakers are not connected properly. Turn this unit off, check the speaker connections and repeat the measurement process from the beginning.
•Be sure to turn off the power before checking speaker connections.
Examples | Error details | Measures |
Audyssey Setup | • The connected setup microphone is broken, or a device other than the | • Connect the included setup microphone to the SETUP MIC jack of this unit. |
Caution! : Please check the cable connection and retry. | supplied setup microphone is connected. |
|
Microphone or Speaker is none | • Not all speakers could be detected. | • Check the speaker connections. |
| Retry |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| • There is too much noise in the room for accurate measurements to be | • Either turn off any device generating noise or move it away. | |
| Audyssey Setup | |||||||||||||
| Caution! |
|
|
|
|
|
|
|
|
|
|
| made. | • Perform again when the surroundings are quieter. |
| Ambient noise is too high or level is too low | • Speaker or subwoofer sound is too low for accurate measurements to be | • Check the speaker installation and the direction in which the speakers are | |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| made. | facing. |
|
|
|
|
|
|
|
|
|
|
|
|
|
| • Adjust the subwoofer’s volume. |
| Retry |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Audyssey Setup | • The displayed speaker could not be detected. | • Check the connections of the displayed speaker. | |||||||||||
| Caution! : Please check the cable connection and retry. | (The screen on the left indicates that the front right speaker cannot be |
| |||||||||||
| Front R | :None | detected.) |
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Retry |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Audyssey Setup |
|
|
| • The displayed speaker is connected with the polarity reversed. | • Check the polarity of the displayed speaker. |
|
| |||
|
|
|
|
|
| ||||||
| Caution! : Please check the cable connection and retry. | (The screen on the left indicates that the polarity phases of the front right | • For some speakers, this error message may be |
|
| ||||||
| Front R | :Phase |
|
|
| speakers are reversed.) | displayed even if the speaker is properly connected. |
|
| ||
|
|
|
|
|
|
|
|
| If you are sure the connection is correct, use o p |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| to select “Skip Error”, then press ENTER. |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Retry | Phase Info. |
| Skip Error |
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 31 |
|
|
| ||
|
|
|
|
| DVD |
|
|
|
| ||
version Basic
version Advanced
Informations