Digi DC-190 Customer Specification 141 Settings, Apw, Switching if Spec 2, bit 1 is set

4.2Customer Specification (141 Settings)

To configure customer specifications, press and hold the REZERO key and enter 141 using the numeric keypad. SPC00 appears in the WEIGHT display and configuration of four bits (for SPEC 0) appears in QUANTITY display. Follow the procedure described in Section 4.1 on page 17 to update the SPEC settings for the 141 access code.

SPEC

Default

Bit 3

Bit 2

Bit 1

Bit 0

0

0000

Transfer Tare Weight

Tare Accumulation

Terminator (RS-232 only)

Piece Weight Selection

0: No (hold tare)

0:

No (overwrite tare)

0: Carriage return

0: Unit wt per 1000

1: Yes (transfer tare)

1: Yes (add to existing

1: Carriage return +

1: Average piece wt

tare)

linefeed

(APW)

1

0000

Power Auto Off Function: Function used to preserve and extend battery life. All four bits are used to

specify the number of minutes (binary) before the scale enters autopower off mode.Examples below show

the binary code, time delay, and description. Settings can range from 0–15 minutes in 1-minute

increments.

Binary Code

8421

Time (min)

Description

0000

0

Autopower off is disabled.

0111

7

If net weight is zero and no motion for 7 minutes, scale goes into autopower off mode.

1111

15

If net weight is zero and no motion for 15 minutes, scale goes into autopower off mode.

NOTE: Powering down means that accumulated value is lost and not retained upon power up. However,

all total inventory values stored with item codes are retained.

2

1000

Scale Specification

Kg/Lb Lamp Enable

Inventory Display by Net/

00: Gram (no units switching)

01: Kg

0: Yes

Gross Key

10: Lb

11: Not used

1: No

0:

No (Net/Gross toggle)

NOTE: Values 01 and 10 allow Lb/Kg units

1:

Yes (INVENT key

shows inventory quantity)

switching if SPEC 2, bit 1 is set 0.

3

0000

RS-232 Port Commands (D-sub)

Print Commands (8-pin DIN)

00: Standard RS-232 (PC, force balance)

00: BCP-30 (barcode printer, force balance)

01:

TM-U295 ticket printer

01:

TM-U295 ticket printer

10: TM-U200 (with or without cutter)

10: TM-U200 (with or without cutter)

11: TM-U200 (with feed for tear-off)

11:

TM-U200 (with feed for tear-off)

4

1001

Set New Item Code

Insufficient Sample Level

Negative Counting

During Normal Mode

00:

0.1%

0:

No

0:

Yes

01:

0.2%

1:

Yes

1:

No

10:

0.0%

5

1011

Sampling Time for Unit

Unit Weight

Date Order

Weight Calculations

Auto-Recomputing

00:

Year, Month, Day

0:

10 times

0:

Press

PIECES

key

01:

Day, Month, Year

1:

5 times

after adding number of

11:

Month, Day, Year

pieces

1:

Scale

automatically

recomputes

after

adding

number

of

pieces without pressing

PIECES key

6

1001

Display Accuracy of

Clear Key Operation

RS-232 Continue

Auto Shift to Next

Unit Weight

0:

Clear all data

Sending Rate to PC

Character After Two Digits

of Teraoka Code Entry

0:

No

1:

Clear last character

0: High

1:

Yes

1: Low

0: No (requires + key)

1:

Yes

Table 4-1. DC-190 141 Settings