Digi DC-190 Spec Min Max, Connector, select, Selecting 1 can damage, Components

SPEC

Default

Bit 3

Bit 2

Bit 1

Bit 0

27

0100

Comma Display

Keypad Entry of Tare

Tare Range

0: No

0: No

00: 100% FS

01:

50% FS

1: Yes

1: Yes

10: 5% FS

11: Not used

28

0000

Auto Tare Clear when

Automatic Unit Weight Clear Condition

Automatic Unit Weight

Rezeroed

00: Over net 5d and gross 21d, weight stable

Clear

0:

No

01: Greater than or equal to net 1d, weight stable

0: No

1:

Yes (REZERO

10: Greater than or equal to net 1d, quantity > 0,

1: Yes

clears tare value)

weight stable

29

0000

Digital Tare Rounding

Tare Value Exchange

Tare Addition

Tare Subtraction

0: Tare exactly

with TARE key

0:Yes (new tare weight

0: Yes (new tare weight

1: Round to nearest

0: Yes (allow tare

added to existing tare)

subtracted from

increment

addition/subtraction)

1:No

existing tare)

1: No

1: No

30

none

Load Cell Sensitivity Selection (mV/V)—PORT 1, Scale 1

Load cell sensitivity is automatically set at calibration. Manual adjustments can be made to reduce noise.

Spec

Min

Max

Spec

Min

Max

Spec

Min

Max

Spec

Min

Max

0000:

3.46

4.00

0100:

1.95

2.25

1000:

1.09

1.27

1100:

0.61

0.71

0001:

3.00

3.46

0101:

1.69

1.95

1001:

0.95

1.09

1101:

0.53

0.91

0010:

2.59

3.00

0110:

1.46

1.69

1010:

0.82

0.95

1110:

0.46

0.53

0011:

2.25

2.59

0111:

1.27

1.46

1011:

0.71

0.82

1111:

0.40

0.46

31

none

Load Cell Sensitivity Selection (mV/V)—PORT 1, Scale 2

Load cell sensitivity is automatically set at calibration. Manual adjustments can be made to reduce noise.

Spec

Min

Max

Spec

Min

Max

Spec

Min

Max

Spec

Min

Max

0000:

3.46

4.00

0100:

1.95

2.25

1000:

1.09

1.27

1100:

0.61

0.71

0001:

3.00

3.46

0101:

1.69

1.95

1001:

0.95

1.09

1101:

0.53

0.91

0010:

2.59

3.00

0110:

1.46

1.69

1010:

0.82

0.95

1110:

0.46

0.53

0011:

2.25

2.59

0111:

1.27

1.46

1011:

0.71

0.82

1111:

0.40

0.46

32

1010

Calibration Mode

Low Battery

Auto Exit from Part

Scale Connected to

Protected by Span

Annunciator Enabled

Accumulation and

PORT 2

Switch

0: Yes

Reduction Mode

0: No

0: Yes (span switch

1: No

0:No (must press

1: Yes

must be pressed

CLEAR to perform

CAUTION: If you are not

before calibration)

another accumulation)

connecting a scale to this

1: No

1:Yes (exits to counting

connector, select 0.

mode after three

Selecting 1 can damage

seconds)

the console’s electronic

components.

33

0___

Over Weight Mask at:

Weight Decimal Point Position (PORT 2, Scale 2 or 3)

0: +1d

MUST BE SET PRIOR TO CALIBRATION!

1: +9d

000: 00000

011: 00.000

001: 0000.0

100: 0.0000

010: 000.00

101: 0.00000

34

0000

Not used

A/D Output (PORT 1,

A/D Filtering (PORT 1, Scale 1)

Scale 1)

00: Normal

0: For std/normal load

01: Protect from small vibration/fast change in

cell

(≤ 18 mV)

display

1: For abnormal load

10: Protect from medium vibration

cell with too large

11: Protect from large vibration, slow change in

offset (> 18mV)

display

Table 4-2. DC-190 142 Settings (Continued)