Digi DC-190 installation manual DIN-8 Force Balance

SPEC	Default		Bit 3		Bit 2		Bit 1				Bit 0
7	0000	Setpoint Buzzer		Setpoint Latch		Setpoint Type
		0:	Yes	0:	Latching	00:	% Quantity		01:	% Weight
		1:	No	1:	Non-latching	10:	Quantity		11:	Weight
NOTE: See Section 3.2.2 on page 16 for more information about configuring SPECs 8–11
8	0010	Force Balance		RS-232C Data Length		RS-232C Baud Rate
		Attached		0:	7 bits	00:	1200	01:	2400
		0:	No	1:	8 bits	10:	4800	11:	9600
		1:	Yes
9	0111	RS-232C Stop Bits		Force Balance Type		RS-232C Parity Bit
		0:	1 bit	0:	Not used	00:	No	01: Odd
		1:	2 bits	1:	Ohaus Explorer	10:	Not used	11: Even
10	0111	Printer or PC Attached		RS-232C Data Length		RS-232C Baud Rate
		0:	No	0:7 bits		00:	1200	01:	2400
		1:	Yes	1:	8 bits	10:	4800	11:	9600
11	0100	RS-232C Stop Bits		Printer Driver		RS-232 Parity Bit
		0:	1 bit	0:	Eltron printer driver	00:	No	01: Odd
		1:	2 bits		or comma-delimited	10:	Not used	11: Even
					file
				1:	BCP30, BCP-300,
					or Epson printer
12	1000	RS-232 (PC/PRN) Output				Eltron Format				RS-232C PC Data Sent
		00:	Not available			0: Eltron fixed label				with Header Codes
		01: When counting condition (PC)					format (also for			0:	Yes
		10: By * key (printer and PC)					BCP30, BCP300)			1:	No
		11:	In both cases			1: Custom download
							format
NOTE: See Section 3.2.1 on page 15 for more information about configuring SPEC 13
13	0001	RS-232 PC Header		RS-232 Connectors
		0:	Header codes	If only one RS-232 device (printer or PC) is connected to the scale, select one of
		1:	Field titles	the four settings below:
					DIN-8 (FORCE BALANCE)			D-Sub (232C/PRINTER)
					000: Force Balance (SPEC 8, 9			Printer (SPEC 10, 11)
					001: Printer (SPEC 10, 11)			Force Balance (SPEC 8, 9)
					100: Force Balance (SPEC 8, 9			PC (SPEC 10, 11)
					101: PC (SPEC 10, 11)			Force Balance (SPEC 8, 9)
				If two RS-232 devices (printer and PC) are connected to the scale, select one of
				the two settings below:
					DIN-8 (FORCE BALANCE)			D-Sub (232C/PRINTER)
					010: PC (SPEC 8, 9)			Printer (SPEC 10, 11)
					011: Printer (SPEC 10, 11			PC (SPEC 8, 9)
NOTE: See Section 10.10 on page 60 for PSC QuickScan 6000 scanner setup information (SPECs 14 and 15).
14	1010	RS-232C Connection		RS-232C Data Length		RS-232C Baud Rate (Barcode pen)
		(Barcode pen)		(Barcode pen)		00:	1200	01:	2400
		0:	No	0:	7 Bits	10:	4800	11:	9600
		1:	Yes	1:	8 Bits

Table 4-1. DC-190 141 Settings (Continued)