Manuals / DKS Enterprises / Communications / Telephone

DKS Enterprises 1815, 1817 Relay Wiring Typical, Controlling a Single Door or Gate, Gate Operator

Models: 1817

1 67

Download 67 pages 63.03 Kb

Page 24

2.3 RELAY WIRING (TYPICAL)

2.3 RELAY WIRING (TYPICAL)

2.3.1 Controlling a Single Door or Gate

Relay 1 is typically used when the system will control a single door or vehicular gate operator. Note that the electric strike and magnetic lock are each powered by their own power supply. Electric strikes are connected through the normally open (NO) contact and magnetic locks are connected through the normally closed (NC) contact.

Relay 0 COM

Relay 0 NC

Relay 0 NO

Relay 0

Relay 2 COM

Relay 2

Relay 1 COM

Relay 1 NC

Relay 1 NO

13 14 15 16 17

Gate Operator

OR

Electric Strike

OR

Magnetic Lock

24

Image 24

DKS Enterprises 1815, 1803PC, 1817 Relay Wiring Typical, Controlling a Single Door or Gate, Gate Operator, Electric Strike

Contents

Owner’s Manual 1803PC, 1815, 1817 PC Programmable Telephone Entry SystemsPage Use this manual with the following models only TABLE OF CONTENTS Section 1 - InstallationSection 2 - Wiring PrefaceSection 4 - Adjustments Section 6 - Maintenance and Trouble ShootingSection 5 - Operating Instructions 5.3 System AdministratorIMPORTANT NOTICE FCC - UNITED STATESDOC - CANADA ListingGENERAL INFORMATION FEATURES SECTION 1 - INSTALLATION 1.1 INSTALLATION GUIDELINES - ALL SYSTEMS1.1.1 Surface Mount Units 1.1.2 Surface Mount Units with Recess Box 1.1.3 Flush Mount Units 1.1.4 Flush Mount Rough-in Box 1.7511.0 1.751.1.5 Flush Mount Trim Ring Rough-inTrim Flush Mount1.1.6 Flush Mount Surface Mounting Kit 1.1.7 Wall Mount Units 1.2 MEMORY CHIP INSTALLATION 1.3 POSTAL LOCK INSTALLATION SECTION 2 - WIRING Connections to 2348 Elevator Control Board OPTIONAL Weigand Power RS-232 Input OPTIONAL2.1 MAIN TERMINAL DESCRIPTION 2.2.1 Weigand Power Terminals 2.2 WEIGAND TERMINAL DESCRIPTION2.2.2 Weigand Data Terminals 2.2.3 Elevator Control Terminals 2.2.4 RS-232 Terminals2.3 RELAY WIRING TYPICAL 2.3.1 Controlling a Single Door or GateGate Operator Electric Strike2.3.2 Controlling a Gate Operator and Pedestrian Gate or Door Gate OperatorElectric Strike Magnetic Lock2.3.3 Controlling a Gate Operator and Two Pedestrian Doors or Gates Magnetic Lock Electric Strike Gate Operator2.3.4 Tracker Expansion Board Control To Tracker Boards To Tracker Boards Gate OperatorPage SECTION 3 - PROGRAMMING 3.1 GENERAL PROGRAMMING INFORMATION3.1.1 Programming with a PC 3.1.2 Programming from the Keypad 3.1.3 System Memory Standard Chip500 MemPLUS Chip Factory setting = Factory setting = Single System3.2 PROGRAMMING WITH A PC 3.2.1 Master CodeFactory Setting = OFF STOP3.2.3 Programming for Call-up Operation 3.2.4 PC Programming TableFactory setting for talk time = 60 seconds 3.3 GENERAL PROGRAMMING3.3.1 Relay Strike Time 3.3.2 Talk Time3.3.4 Postal Switch Factory setting is Relay 0 = ####, Relay 1 = 9876, Relay 2 =3.3.3 Tone Open Numbers Factory setting =Factory setting = touch-tone 3.3.5 Touch-tone / Rotary-dial3.3.6 Rotary-dial Factory setting =3.4 PROGRAMMING LETTERS, NUMBERS and MESSAGES 3.4.1 Programming Letters and Numbers3.4.2 Programming the User Message - 1815 Systems 3.4.3 Programming the Instruction Message - 1815 Systems 3.4.4 Programming the User Message - 1817 Systems 3.4.5 Programming the Instruction Message - 1817 Systems 3.5 Programming Phone Numbers and Names To Enter JONES APTFactory setting is three 3 digits 3.5.1 Programming the Directory Code Length3.5.2 Programming 7-digit Phone Numbers 99993.5.3 Programming Area Codes 3.5.4 Programming Phone Numbers with Area Code Reference3.5.5 Programming Names 1815, 1817 Systems Only 3.5.6 Deleting Individual Phone Numbers3.5.7 Delete Names 1815, 1817 Systems Only 3.5.8 Delete Area Codes 3.5.9 Display Phone Numbers 1815, 1817 Systems Only3.6 PROGRAMMING DEVICE CODES 3.6.1 Programming Device Codes3.6.2 Deleting Device Codes 3.7 FOUR-DIGIT ENTRYT CODES 3.7.1 Programming Four-digit Entry Codes3.7.2 Delete Four-digit Entry Codes 3.7.3 Entry Code RangesSECTION 4 - ADJUSTMENTS 4.1 Speaker Volume4.2 Feedback 4.3 Click Sensitivity4.7 Master Code Switch 4.6 Back-light Cutoff 1817 Only4.8 Ring Pin 4.9 Relay 2 Contact Pin1815 Adjustment Locations VOLUME AUTO FEEDBACK HF HS RING PINSEC LEVEL CONTRAST1817 Adjustment Locations VOLUME AUTO FEEDBACK HF HS RING PINSEC LEVEL BACK LIGHT CONTRAST LOWERSECTION 5 - OPERATING INSTRUCTIONS 5.1 Guest Instructions5.2.2 Using an Entry Code 5.2 RESIDENT INSTRUCTIONS5.2.1 Responding to a Guest Call 5.3 SYSTEM ADMINISTRATOR 5.3.2 Tracker Board Override Hold Open Command5.3.1 Opening from a Remote Location 5.3.3 Relay Check 5.3.4 Time and Date Check5.4 MISCELLANEOUS OPERATING INSTRUCTIONS 5.4.1 Talk Time5.4.2 Line Sharing 5.4.3 Connection to a PBXPage SECTION 6 - MAINTENANCE 6.1 TROUBLE SHOOTINGPOSSIBLE SOLUTIONS SYMPTON6.1.1 RS-232 Test will be erased when this function is performed6.1.2 Weigand Test 1815, 1817 Systems Only 6.1.3 Elevator Boards Hardware Test6.1.4 Elevator Board / Floor Hardware Test 6.2 ACCESSORIES 6.3 LOG TABLES Smith, JohnMOMENTARY ACTIVATION CONTINUOUS ACTIVATION RELEASE ACTIVATE 1 HOUR LOW BOUNDRYNAME PHONE NUMBERDIR CODE ENT CODEGranting or Denying Access Access CodeResident Instruction Sheet Guest Communication