Manuals / DKS Enterprises / Communications / Telephone

DKS Enterprises 1817, 1815, 1803PC Controlling a Gate Operator and Two Pedestrian Doors or Gates

Models: 1817

1 67

Download 67 pages 63.03 Kb

Page 26

2.3.3 Controlling a Gate Operator and Two Pedestrian Doors (or Gates)

2.3.3 Controlling a Gate Operator and Two Pedestrian Doors (or Gates)

The diagram below shows how it is possible to control a gate operator and two pedestrian doors or gates from the system. Relay 0 is typically used to control the gate operator and relays 1 and 2 are used to control pedestrian doors and/or gates. Note that the electric strike and the magnetic lock are powered from their own power supply. The relay 2 contact is set to either normally open (NO) for electric strikes, or normally closed (NC) for magnetic locks by placing the relay 2 contact shorting bar on either the NO or NC pins.

A variation of this diagram is for the system to control three doors, or two gate operators (entry and exit) and a door, or three gate operators.

Relay 0	Relay 0 NO Relay 0 NC Relay 0 COM	Relay 2 COM	Relay 2	Relay 1 COM	Relay 1 NC	Relay 1 NO
		13	14	15	16	17
						AND
						AND

Magnetic Lock

Electric Strike

Gate Operator

26

Image 26

DKS Enterprises 1817, 1815, 1803PC owner manual Controlling a Gate Operator and Two Pedestrian Doors or Gates

Contents

Owner’s Manual 1803PC, 1815, 1817 PC Programmable Telephone Entry SystemsPage Use this manual with the following models only Section 2 - Wiring TABLE OF CONTENTSSection 1 - Installation PrefaceSection 5 - Operating Instructions Section 4 - AdjustmentsSection 6 - Maintenance and Trouble Shooting 5.3 System AdministratorDOC - CANADA IMPORTANT NOTICEFCC - UNITED STATES ListingGENERAL INFORMATION FEATURES SECTION 1 - INSTALLATION 1.1 INSTALLATION GUIDELINES - ALL SYSTEMS1.1.1 Surface Mount Units 1.1.2 Surface Mount Units with Recess Box 1.1.3 Flush Mount Units 11.0 1.1.4 Flush Mount Rough-in Box1.75 1.75Trim 1.1.5 Flush Mount Trim RingRough-in Flush Mount1.1.6 Flush Mount Surface Mounting Kit 1.1.7 Wall Mount Units 1.2 MEMORY CHIP INSTALLATION 1.3 POSTAL LOCK INSTALLATION SECTION 2 - WIRING Connections to 2348 Elevator Control Board OPTIONAL Weigand Power RS-232 Input OPTIONAL2.1 MAIN TERMINAL DESCRIPTION 2.2.2 Weigand Data Terminals 2.2.1 Weigand Power Terminals2.2 WEIGAND TERMINAL DESCRIPTION 2.2.3 Elevator Control Terminals 2.2.4 RS-232 TerminalsGate Operator 2.3 RELAY WIRING TYPICAL2.3.1 Controlling a Single Door or Gate Electric StrikeElectric Strike 2.3.2 Controlling a Gate Operator and Pedestrian Gate or DoorGate Operator Magnetic Lock2.3.3 Controlling a Gate Operator and Two Pedestrian Doors or Gates Magnetic Lock Electric Strike Gate Operator2.3.4 Tracker Expansion Board Control To Tracker Boards To Tracker Boards Gate OperatorPage 3.1.1 Programming with a PC SECTION 3 - PROGRAMMING3.1 GENERAL PROGRAMMING INFORMATION 3.1.2 Programming from the Keypad 500 MemPLUS Chip 3.1.3 System MemoryStandard Chip 3.2 PROGRAMMING WITH A PC Factory setting =Factory setting = Single System 3.2.1 Master Code3.2.3 Programming for Call-up Operation Factory Setting = OFFSTOP 3.2.4 PC Programming Table3.3.1 Relay Strike Time Factory setting for talk time = 60 seconds3.3 GENERAL PROGRAMMING 3.3.2 Talk Time3.3.3 Tone Open Numbers 3.3.4 Postal SwitchFactory setting is Relay 0 = ####, Relay 1 = 9876, Relay 2 = Factory setting =3.3.6 Rotary-dial Factory setting = touch-tone3.3.5 Touch-tone / Rotary-dial Factory setting =3.4 PROGRAMMING LETTERS, NUMBERS and MESSAGES 3.4.1 Programming Letters and Numbers3.4.2 Programming the User Message - 1815 Systems 3.4.3 Programming the Instruction Message - 1815 Systems 3.4.4 Programming the User Message - 1817 Systems 3.4.5 Programming the Instruction Message - 1817 Systems 3.5 Programming Phone Numbers and Names To Enter JONES APT3.5.2 Programming 7-digit Phone Numbers Factory setting is three 3 digits3.5.1 Programming the Directory Code Length 99993.5.3 Programming Area Codes 3.5.4 Programming Phone Numbers with Area Code Reference3.5.7 Delete Names 1815, 1817 Systems Only 3.5.5 Programming Names 1815, 1817 Systems Only3.5.6 Deleting Individual Phone Numbers 3.5.8 Delete Area Codes 3.5.9 Display Phone Numbers 1815, 1817 Systems Only3.6.2 Deleting Device Codes 3.6 PROGRAMMING DEVICE CODES3.6.1 Programming Device Codes 3.7.2 Delete Four-digit Entry Codes 3.7 FOUR-DIGIT ENTRYT CODES3.7.1 Programming Four-digit Entry Codes 3.7.3 Entry Code Ranges4.2 Feedback SECTION 4 - ADJUSTMENTS4.1 Speaker Volume 4.3 Click Sensitivity4.8 Ring Pin 4.7 Master Code Switch4.6 Back-light Cutoff 1817 Only 4.9 Relay 2 Contact PinSEC LEVEL 1815 Adjustment LocationsVOLUME AUTO FEEDBACK HF HS RING PIN CONTRASTSEC LEVEL BACK LIGHT 1817 Adjustment LocationsVOLUME AUTO FEEDBACK HF HS RING PIN CONTRAST LOWERSECTION 5 - OPERATING INSTRUCTIONS 5.1 Guest Instructions5.2.1 Responding to a Guest Call 5.2.2 Using an Entry Code5.2 RESIDENT INSTRUCTIONS 5.3.1 Opening from a Remote Location 5.3 SYSTEM ADMINISTRATOR5.3.2 Tracker Board Override Hold Open Command 5.3.3 Relay Check 5.3.4 Time and Date Check5.4.2 Line Sharing 5.4 MISCELLANEOUS OPERATING INSTRUCTIONS5.4.1 Talk Time 5.4.3 Connection to a PBXPage SECTION 6 - MAINTENANCE 6.1 TROUBLE SHOOTINGPOSSIBLE SOLUTIONS SYMPTON6.1.1 RS-232 Test will be erased when this function is performed6.1.2 Weigand Test 1815, 1817 Systems Only 6.1.3 Elevator Boards Hardware Test6.1.4 Elevator Board / Floor Hardware Test 6.2 ACCESSORIES MOMENTARY ACTIVATION CONTINUOUS ACTIVATION RELEASE ACTIVATE 1 HOUR 6.3 LOG TABLESSmith, John LOW BOUNDRYDIR CODE NAMEPHONE NUMBER ENT CODEResident Instruction Sheet Granting or Denying AccessAccess Code Guest Communication