Manuals / DKS Enterprises / Communications / Telephone

DKS Enterprises 1803PC Controlling a Gate Operator and Pedestrian Gate or Door, Electric Strike

Models: 1817

1 67

Download 67 pages 63.03 Kb

Page 25

2.3.2 Controlling a Gate Operator and Pedestrian Gate (or Door)

2.3.2 Controlling a Gate Operator and Pedestrian Gate (or Door)

When controlling a gate operator and pedestrian gate (or door), relay 1 is typically used to control the gate operator while relay 2 is typically used to control the door or gate. Note that the electric strike and the magnetic lock are powered from their own power supply. The relay 2 contact is set to either normally open (NO) for electric strikes, or normally closed (NC) for magnetic locks by placing the relay 2 contact shorting bar on either the NO or NC pins.

A variation of this diagram is for the system to control two doors or two gates.

Relay 0 COM

Relay 0 NC

Relay 0 NO

Relay 0

Relay 2 COM

Relay 2

Relay 1 COM

Relay 1 NC

Relay 1 NO

13 14 15 16 17

Gate Operator

AND

Electric Strike

OR

Magnetic Lock

25

Image 25

DKS Enterprises 1803PC, 1815, 1817 Controlling a Gate Operator and Pedestrian Gate or Door, Electric Strike, Magnetic Lock

Contents

1803PC, 1815, 1817 PC Programmable Telephone Entry Systems Owner’s ManualPage Use this manual with the following models only Section 1 - Installation TABLE OF CONTENTSSection 2 - Wiring PrefaceSection 6 - Maintenance and Trouble Shooting Section 4 - AdjustmentsSection 5 - Operating Instructions 5.3 System AdministratorFCC - UNITED STATES IMPORTANT NOTICEDOC - CANADA ListingGENERAL INFORMATION FEATURES 1.1 INSTALLATION GUIDELINES - ALL SYSTEMS SECTION 1 - INSTALLATION1.1.1 Surface Mount Units 1.1.2 Surface Mount Units with Recess Box 1.1.3 Flush Mount Units 1.75 1.1.4 Flush Mount Rough-in Box11.0 1.75Rough-in 1.1.5 Flush Mount Trim RingTrim Flush Mount1.1.6 Flush Mount Surface Mounting Kit 1.1.7 Wall Mount Units 1.2 MEMORY CHIP INSTALLATION 1.3 POSTAL LOCK INSTALLATION SECTION 2 - WIRING RS-232 Input OPTIONAL Connections to 2348 Elevator Control Board OPTIONAL Weigand Power2.1 MAIN TERMINAL DESCRIPTION 2.2 WEIGAND TERMINAL DESCRIPTION 2.2.1 Weigand Power Terminals2.2.2 Weigand Data Terminals 2.2.4 RS-232 Terminals 2.2.3 Elevator Control Terminals2.3.1 Controlling a Single Door or Gate 2.3 RELAY WIRING TYPICALGate Operator Electric StrikeGate Operator 2.3.2 Controlling a Gate Operator and Pedestrian Gate or DoorElectric Strike Magnetic LockMagnetic Lock Electric Strike Gate Operator 2.3.3 Controlling a Gate Operator and Two Pedestrian Doors or GatesTo Tracker Boards To Tracker Boards Gate Operator 2.3.4 Tracker Expansion Board ControlPage 3.1 GENERAL PROGRAMMING INFORMATION SECTION 3 - PROGRAMMING3.1.1 Programming with a PC 3.1.2 Programming from the Keypad Standard Chip 3.1.3 System Memory500 MemPLUS Chip Factory setting = Single System Factory setting =3.2 PROGRAMMING WITH A PC 3.2.1 Master CodeSTOP Factory Setting = OFF3.2.3 Programming for Call-up Operation 3.2.4 PC Programming Table3.3 GENERAL PROGRAMMING Factory setting for talk time = 60 seconds3.3.1 Relay Strike Time 3.3.2 Talk TimeFactory setting is Relay 0 = ####, Relay 1 = 9876, Relay 2 = 3.3.4 Postal Switch3.3.3 Tone Open Numbers Factory setting =3.3.5 Touch-tone / Rotary-dial Factory setting = touch-tone3.3.6 Rotary-dial Factory setting =3.4.1 Programming Letters and Numbers 3.4 PROGRAMMING LETTERS, NUMBERS and MESSAGES3.4.2 Programming the User Message - 1815 Systems 3.4.3 Programming the Instruction Message - 1815 Systems 3.4.4 Programming the User Message - 1817 Systems 3.4.5 Programming the Instruction Message - 1817 Systems To Enter JONES APT 3.5 Programming Phone Numbers and Names3.5.1 Programming the Directory Code Length Factory setting is three 3 digits3.5.2 Programming 7-digit Phone Numbers 99993.5.4 Programming Phone Numbers with Area Code Reference 3.5.3 Programming Area Codes3.5.6 Deleting Individual Phone Numbers 3.5.5 Programming Names 1815, 1817 Systems Only3.5.7 Delete Names 1815, 1817 Systems Only 3.5.9 Display Phone Numbers 1815, 1817 Systems Only 3.5.8 Delete Area Codes3.6.1 Programming Device Codes 3.6 PROGRAMMING DEVICE CODES3.6.2 Deleting Device Codes 3.7.1 Programming Four-digit Entry Codes 3.7 FOUR-DIGIT ENTRYT CODES3.7.2 Delete Four-digit Entry Codes 3.7.3 Entry Code Ranges4.1 Speaker Volume SECTION 4 - ADJUSTMENTS4.2 Feedback 4.3 Click Sensitivity4.6 Back-light Cutoff 1817 Only 4.7 Master Code Switch4.8 Ring Pin 4.9 Relay 2 Contact PinVOLUME AUTO FEEDBACK HF HS RING PIN 1815 Adjustment LocationsSEC LEVEL CONTRASTVOLUME AUTO FEEDBACK HF HS RING PIN 1817 Adjustment LocationsSEC LEVEL BACK LIGHT CONTRAST LOWER5.1 Guest Instructions SECTION 5 - OPERATING INSTRUCTIONS5.2 RESIDENT INSTRUCTIONS 5.2.2 Using an Entry Code5.2.1 Responding to a Guest Call 5.3.2 Tracker Board Override Hold Open Command 5.3 SYSTEM ADMINISTRATOR5.3.1 Opening from a Remote Location 5.3.4 Time and Date Check 5.3.3 Relay Check5.4.1 Talk Time 5.4 MISCELLANEOUS OPERATING INSTRUCTIONS5.4.2 Line Sharing 5.4.3 Connection to a PBXPage 6.1 TROUBLE SHOOTING SECTION 6 - MAINTENANCESYMPTON POSSIBLE SOLUTIONSwill be erased when this function is performed 6.1.1 RS-232 Test6.1.3 Elevator Boards Hardware Test 6.1.2 Weigand Test 1815, 1817 Systems Only6.1.4 Elevator Board / Floor Hardware Test 6.2 ACCESSORIES Smith, John 6.3 LOG TABLESMOMENTARY ACTIVATION CONTINUOUS ACTIVATION RELEASE ACTIVATE 1 HOUR LOW BOUNDRYPHONE NUMBER NAMEDIR CODE ENT CODEAccess Code Granting or Denying AccessResident Instruction Sheet Guest Communication