Manuals / DKS Enterprises / Communications / Telephone

DKS Enterprises 1815, 1803PC, 1817 owner manual Tracker Expansion Board Control

Models: 1817

1 67

Page 27

2.3.4 Tracker Expansion Board Control

When Tracker expansion boards are used with the system to control up to 16 additional entry points, relays 1 and 2 are designated as tracker command relays and connect to the Tracker expansion boards. In this diagram, relay 0 is used to control the gate operator and relays 1 and 2 are connected to the tracker expansion boards. The relay 2 shorting bar is set for normally open (NO) contacts.

For more information on Tracker expansion boards and wiring, refer to the Tracker Board Installation Manual, P/N 2351-065.

Relay 0	Relay 0 NO Relay 0 NC Relay 0 COM	Relay 2 COM	Relay 2	Relay 1 COM	Relay 1 NC	Relay 1 NO
		13	14	15	16	17

To Tracker Boards 9-16

To Tracker Boards 1-8

Gate Operator

Page 27

Image 27

DKS Enterprises 1815, 1803PC, 1817 Tracker Expansion Board Control, To Tracker Boards To Tracker Boards Gate Operator

Contents

1803PC, 1815, 1817 PC Programmable Telephone Entry Systems Owner’s ManualPage Use this manual with the following models only Preface TABLE OF CONTENTSSection 1 - Installation Section 2 - Wiring5.3 System Administrator Section 4 - AdjustmentsSection 6 - Maintenance and Trouble Shooting Section 5 - Operating InstructionsListing IMPORTANT NOTICEFCC - UNITED STATES DOC - CANADAGENERAL INFORMATION FEATURES 1.1 INSTALLATION GUIDELINES - ALL SYSTEMS SECTION 1 - INSTALLATION1.1.1 Surface Mount Units 1.1.2 Surface Mount Units with Recess Box 1.1.3 Flush Mount Units 1.75 1.1.4 Flush Mount Rough-in Box1.75 11.0Flush Mount 1.1.5 Flush Mount Trim RingRough-in Trim1.1.6 Flush Mount Surface Mounting Kit 1.1.7 Wall Mount Units 1.2 MEMORY CHIP INSTALLATION 1.3 POSTAL LOCK INSTALLATION SECTION 2 - WIRING RS-232 Input OPTIONAL Connections to 2348 Elevator Control Board OPTIONAL Weigand Power2.1 MAIN TERMINAL DESCRIPTION 2.2.1 Weigand Power Terminals 2.2 WEIGAND TERMINAL DESCRIPTION2.2.2 Weigand Data Terminals 2.2.4 RS-232 Terminals 2.2.3 Elevator Control TerminalsElectric Strike 2.3 RELAY WIRING TYPICAL2.3.1 Controlling a Single Door or Gate Gate OperatorMagnetic Lock 2.3.2 Controlling a Gate Operator and Pedestrian Gate or DoorGate Operator Electric StrikeMagnetic Lock Electric Strike Gate Operator 2.3.3 Controlling a Gate Operator and Two Pedestrian Doors or GatesTo Tracker Boards To Tracker Boards Gate Operator 2.3.4 Tracker Expansion Board ControlPage SECTION 3 - PROGRAMMING 3.1 GENERAL PROGRAMMING INFORMATION3.1.1 Programming with a PC 3.1.2 Programming from the Keypad 3.1.3 System Memory Standard Chip500 MemPLUS Chip 3.2.1 Master Code Factory setting =Factory setting = Single System 3.2 PROGRAMMING WITH A PC3.2.4 PC Programming Table Factory Setting = OFFSTOP 3.2.3 Programming for Call-up Operation3.3.2 Talk Time Factory setting for talk time = 60 seconds3.3 GENERAL PROGRAMMING 3.3.1 Relay Strike TimeFactory setting = 3.3.4 Postal SwitchFactory setting is Relay 0 = ####, Relay 1 = 9876, Relay 2 = 3.3.3 Tone Open NumbersFactory setting = Factory setting = touch-tone3.3.5 Touch-tone / Rotary-dial 3.3.6 Rotary-dial3.4.1 Programming Letters and Numbers 3.4 PROGRAMMING LETTERS, NUMBERS and MESSAGES3.4.2 Programming the User Message - 1815 Systems 3.4.3 Programming the Instruction Message - 1815 Systems 3.4.4 Programming the User Message - 1817 Systems 3.4.5 Programming the Instruction Message - 1817 Systems To Enter JONES APT 3.5 Programming Phone Numbers and Names9999 Factory setting is three 3 digits3.5.1 Programming the Directory Code Length 3.5.2 Programming 7-digit Phone Numbers3.5.4 Programming Phone Numbers with Area Code Reference 3.5.3 Programming Area Codes3.5.5 Programming Names 1815, 1817 Systems Only 3.5.6 Deleting Individual Phone Numbers3.5.7 Delete Names 1815, 1817 Systems Only 3.5.9 Display Phone Numbers 1815, 1817 Systems Only 3.5.8 Delete Area Codes3.6 PROGRAMMING DEVICE CODES 3.6.1 Programming Device Codes3.6.2 Deleting Device Codes 3.7.3 Entry Code Ranges 3.7 FOUR-DIGIT ENTRYT CODES3.7.1 Programming Four-digit Entry Codes 3.7.2 Delete Four-digit Entry Codes4.3 Click Sensitivity SECTION 4 - ADJUSTMENTS4.1 Speaker Volume 4.2 Feedback4.9 Relay 2 Contact Pin 4.7 Master Code Switch4.6 Back-light Cutoff 1817 Only 4.8 Ring PinCONTRAST 1815 Adjustment LocationsVOLUME AUTO FEEDBACK HF HS RING PIN SEC LEVELCONTRAST LOWER 1817 Adjustment LocationsVOLUME AUTO FEEDBACK HF HS RING PIN SEC LEVEL BACK LIGHT5.1 Guest Instructions SECTION 5 - OPERATING INSTRUCTIONS5.2.2 Using an Entry Code 5.2 RESIDENT INSTRUCTIONS5.2.1 Responding to a Guest Call 5.3 SYSTEM ADMINISTRATOR 5.3.2 Tracker Board Override Hold Open Command5.3.1 Opening from a Remote Location 5.3.4 Time and Date Check 5.3.3 Relay Check5.4.3 Connection to a PBX 5.4 MISCELLANEOUS OPERATING INSTRUCTIONS5.4.1 Talk Time 5.4.2 Line SharingPage 6.1 TROUBLE SHOOTING SECTION 6 - MAINTENANCESYMPTON POSSIBLE SOLUTIONSwill be erased when this function is performed 6.1.1 RS-232 Test6.1.3 Elevator Boards Hardware Test 6.1.2 Weigand Test 1815, 1817 Systems Only6.1.4 Elevator Board / Floor Hardware Test 6.2 ACCESSORIES LOW BOUNDRY 6.3 LOG TABLESSmith, John MOMENTARY ACTIVATION CONTINUOUS ACTIVATION RELEASE ACTIVATE 1 HOURENT CODE NAMEPHONE NUMBER DIR CODEGuest Communication Granting or Denying AccessAccess Code Resident Instruction Sheet