3.4.2 Programming the User Message – 1815 Systems
The user message, followed by the instruction message, scrolls across the screen from right to left when the system is not in use. Both the user and instruction message can be programmed to display your own message. The user message can be a maximum of 48 characters (spaces count as a character) and is entered into the system memory in three blocks. The first two blocks contain 20 characters while the third block contains 8 characters. The example below shows how the sample message was divided into three blocks. Use the blank matrix to organize your own message. Only upper case letters, numbers and spaces can be programmed from the system keypad.
Factory Default User Message = This Space is For Your User Programmable Message
NOTE: The factory default message was programmed from a PC, therefore upper and lower case letters are displayed.
Example | THANK YOU FOR VISITING OAKWOOD CONDOMINIUMS |
|
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | 18 | 19 | 20 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Block 1 | T | H | A | N | K |
| Y | O | U |
| F | O | R |
| V | I | S | I | T | I |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Block 2 | N | G |
| O | A | K | W | O | O | D |
| C | O | N | D | O | M | I | N | I |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Block 3 | U | M | S |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | 18 | 19 | 20 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Block 1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Block 2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Block 3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
After organizing the user message in the matrix above, follow the instructions below to enter the message into the system. After each desired letter, number or space is displayed on the directory, remember to press * to enter that character. Spaces count as a character and must be entered into memory as a character. After a complete block has been entered, press * to enter the block, then start the next block.
1.Press *80 and enter the
2.Enter the characters into block 1. Remember to press * (beep) after each character.
3.After the last character in block 1 has been entered, press * (beep) to enter the entire block. The screen will display: BLOCK 2.
4.Enter the characters into block 2. Remember to press * (beep) after each character.
5.After the last character in block 2 has been entered, press * (beep) to enter the entire block. The screen will display: BLOCK 3.
6.Enter the characters into block 3. Remember to press * (beep) after each character.
7.After the last character in block 3 has been entered, press * (beep) to enter the entire block.
8.Press * to enter all three blocks into the system memory.
9.Press 0# together to end this programming step (beeeeeep).
10.The new user message will begin to scroll across the screen.
38
