DSCover Satellite Products PC1555MX Appendix A Reporting Codes, Contact ID, Burg - Entry/Exit

Appendix A: Reporting Codes

The following tables contain Contact ID and Automatic SIA for- mat reporting codes. For more information on reporting code formats and notes about individual reporting codes, see sec- tions 5.8 “Communicator – Reporting Codes” on page 17 and

5.9“Communicator – Reporting Formats” on page 18.

Contact ID

The first digit (in parentheses) will automatically be sent by the control. The second two digits are programmed to indicate spe- cific information about the signal.

For example, if zone 1 is an entry/exit point, you could program the event code as [34]. The central station would receive the following:

*BURG - ENTRY/EXIT - 1

where the “1” indicates which zone went into alarm.

SIA Format - Level 2 (Hardcoded)

The SIA communication format used in this product follows the level 2 specifications of the SIA Digital Communication Stan- dard - January 1996. This format will send the Account Code along with its data transmission. The transmission would look similar to the following at the receiver:

N Ri01		BA 01
N	=	New Event
Ri01	=	Partition /Area Identifier
BA	=	Burglary Alarm
01	=	Zone 1

			Dialer	Automatic	SIA Auto Rep
Section #	Reporting Code	Code Sent When...		Contact ID
			Direction*		Codes**
				Codes
[320]	Zone Alarms	zone goes into alarm	A/R	(1) 3A	See Table 3
[324]	Zone Restorals	alarm condition has been restored	A/R	(1) 3A
[330]	Zone Tamper/Restoral	zone exhibits a tamper condition/tamper condition	T/R	(1) 44	TA-ZZ/TR-ZZ
[334]		restored
[328]	Duress Alarm	duress code entered at keypad	A/R	(1) 21	HA-00
[328]	Opening After Alarm	system disarmed with alarm in memory	A/R	(4) A6	OR-00
[328]	Recent Closing	alarm occurs within two minutes of system arming	A/R	(4) 59	CR-00
[328]	Zone Expander Supervi-	panel loses/restores supervisory transmission over the	A/R	(1) 43	UA-00/UH-00
	sory Alarm/Rest.	Keybus from enrolled PC5132 module or keypads with
		zone inputs
[328]	Cross Zone (Police Code)	two zones on the same partition go into alarm during	A/R	(1) 4A	BV-00
	Alarm	any given armed-to-armed period (incl. 24Hr zones)
[329]	[F] Key Alarm/Rest.	Keypad fire alarm (alarm and restore rep. codes sent	A/R	(1) 15	FA-00/FH-00
		together)
[329]	[A] Key Alarm/Rest.	Keypad auxiliary alarm (alarm and restore rep. codes	A/R	(1) AA	MA-00/MH-00
		sent together)
[329]	[P] Key Alarm/Rest.	Keypad panic alarm (alarm and restore rep. codes sent	A/R	(1) 2A	PA-00/PH-00
		together)
[329]	PGM2 Alarm/Rest.	a panic button wired to PGM2 is pressed / access code	A/R	(1) 4A	UA-99/UH-99
		is entered (PGM2 programmed as option [23] or [24])
		a 2-wire smoke detector wired to PGM2 goes into alarm/	A/R	(1) 11	FA-99/FH-99
		alarm is cleared (PGM2 programmed as option [04])
[338]	General System Tamper/	enrolled module with tamper inputs has a tamper alarm/	T/R	(1) 45	TA-00/TR-00
	Rest.	all module tampers restored
[338]	Keypad Lockout	max. number of incorrect access codes has been	T/R	(4) 21	JA-00
		entered at a keypad
[339-343]	Closings	system armed (user 01-34, 40-42 indicated)	O/C	(4) A2	CL-UU
[343]	Partial Closing	one or more zones bypassed when system armed	O/C	(4) 7A	CG-ZZ
[343]	Special Closing	Closing (arming) using one of the following methods:	O/C	(4) AA	CL-00
		quick arm, auto arm, keyswitch, function key, mainte-
		nance code, DLS software
[344-348]	Openings	system disarmed (user 01-34, 40-42 indicated)	O/C	(4) A2	OP-UU
[348]	Auto Arm Cancellation	auto arm cancelled	O/C	(4) A5	CE-00
[348]	Special Opening	Opening (disarming) using one of the following meth-	O/C	(4) AA	OP-00
		ods: keyswitch, maintenance code, DLS software
[349-350]	Battery Trouble/Rest.	PC1555MX battery is low/battery restored	MA/R	(3) A2	YT-00/YR-00

* A/R = alarms/restorals; T/R = tampers/restorals; O/C = openings/closings; MA/R = miscellaneous alarms/restorals; T = test transmissions ** UU = user number (user01-42); ZZ = zone number (01-32)

WWW.DIYALARMFORUM.COM

42