138, Next Select User Certificate, then Next | Dynalink RTA1025W

ADSL Router User Manual

4.Make sure that Request a certificate is selected, and click

Next.

5.Select User Certificate, then Next.

6.Click Submit in the following step.

138

Image 151

Dynalink RTA1025W user manual 138, Next Select User Certificate, then Next

Contents

ADSL2+ Wireless Modem Router User’s Manual Copyright Notice For Using For InstallationFor Service FCC Contents Web Configuration VII Viii ADSL2 Compliance FeaturesUnpacking Adsl Compliance ATM Features Wireless LAN ComplianceBridging Features Security Features Routing FeaturesConfiguration and Management Subscription for Adsl Service Physical Outlook LED IndicatorsFront Panel Rear Panel Choosing a place for the Adsl Router System Requirement Connecting the Adsl Router For Windows ME USB Driver InstallationFor Windows Page For Windows XP Page Right-click on My Computer and press Properties For Windows Vista System Requirement and Installation Page System Requirement and Installation Page System Requirement and Installation Click Device Manager On the Control Panel folder, click System and Maintenance System Requirement and Installation Method One Uninstalling the USB DriverMethod Two System Requirement and Installation Method Two System Requirement and Installation Unplug your USB cable between your router and your PC System Requirement and Installation Click System and Maintenance Press System Page Method Two uninstall from program list Page Setting up TCP/IP Page System Requirement and Installation Highlight Protocol and click Add System Requirement and Installation For Windows NT Highlight TCP/IP Protocol and click OK Enable Obtain an IP address from a Dhcp server and click OK For Windows Page Obtain an IP address automatically. Then click OK Click Internet Protocol TCP/IP and then click OK Connection Click Internet ProtocolTCP/IP and then click OK When it returns to the General Tab on the Local Area Click Network Internet Select Network and Sharing Center Click Manage Network Connection on the left side System Requirement and Installation For Windows 98/ME Renewing IP Address on Client PC For Windows NT/2000/XP Released IP Address For Windows Vista Page Accessing the Internet Primary IP address Subnet Mask PPP over ATM PPPoA ModeConfiguration Description Go to Advanced Internet Connections. And click Add PPP over ATM PPPoA IP Extension ModeVCI PPP over Ethernet PPPoE Mode ISP PPP over Ethernet PPPoE IP Extension Mode Primary IP Address Numbered IP over ATM IPoA Preferred DNS server IP Address Numbered IP over ATM IPoA+NAT Start IP Address End IP Address Check Dhcp Server Off and click Next Unnumbered IP over ATM IPoA IP Address Primary DNS server Secondary DNS server Unnumbered IP over ATM IPoA+NAT Subnet mask 255.255.255.248 Click Next Bridge Mode Start IP Address192.168.1.2 End IP Address Primary IP address192.168.1.1Page Using Web-Based Manager Web Configuration Title Main Menu Window Current Version To Have the New Settings Take EffectOutline of Web Manager Language Auto Scan Internet Connection PVC Quick SetupQuick Start Connect to Internet PPP over ATM/ PPP over Ethernet Connection Type Dhcp Server On Dial on DemandManually Connect Secondary IP Address & Subnet MaskPage Use the following DNS server addresses None Dhcp Server On Bridging Page Overview Status Adsl BER Test Adsl Line Dhcp Table Wireless ClientsInternet Connection Traffic Statistics Domain Name Advanced SetupLocal Network IP Address Host Name Relay On Local Network Dhcp ServerServer and Relay Off Local Network Igmp Snooping Local Network UPnP Web Configuration Adding a New One Internet Connections Vlan ID 802.1Q Vlan Tagging Add Default Route Internet Connection Igmp Proxy EnabledInternet DNS Server Internet Igmp Proxy Seamless Rate Adaptation Enable Adsl PortInternet Adsl Bitswap WAN Interface IP Routing Static RouteNetmask Gateway IP Address Operation EnabledIP Routing Dynamic Routing RIP Version IP Address seen by Internet Users Virtual Server Port Forwarding User defined Pre-defined Virtual Server Port Triggering Virtual Server Dynamic DNS Virtual Server DMZ Host IP Address： Virtual Server Static DNS Enable VPN ALG NAT ALG ConfigurationEnable SIP ALG Firewall Bridge Filtering Firewall Select the direction to filter packets Firewall IP Filtering Port Range Allow TrafficProtocol Source/Destination IP address 100 101 Quality of ServiceFirst generation Precedence and type of service bits Second generation Differentiated services code point 802.1p Priority Quality of Service Bridge QoS102 Traffic Class Name 103 Quality of Service IP QoSWAN 802.1p 104 Available Interfaces Port Mapping105 Group Name 106 Basic Settings Wireless107 108 109 Select Wireless NetworkWireless Security Security Key 1 to Authentication Type110 Format Radius Shared Secret For 802.1X Wireless Network802.1x environment Configuration 111 112 For WPA Wi-Fi Protected Access For WPA-PSK WPA2-PSK Mixed WPA2/WPA-PSK 113Pre-Share Key Network Re-auth Interval WPA2 Pre-authentication114 For WPA-2 Mixed WPA2/WPA MAC Address of Wireless adaptor Access ControlAccess Control View Access Control List Search Other Repeaters AP ModeRepeater 116 117 DiagnosticsPress Run Diagnostic Tests on Management Management Control From Remote Management Accounts118 Management Control From Local TR-069 Client Configuration119 Identify the Validation of Certificate from ACS 120 121 122 Internet Time Log Level Configuring System LogSystem Log 123 124 System Log ConfigurationMode Viewing System Log Remote Side Server 125 Viewing System Log Local Side Adsl Router 126 127 Backup Config 128 Update FirmwareReset Router Restore 129 UPnP for XP 130 131 Problems with LANProblems with WAN PC on the LAN cannot access the Web page of the Adsl Router 132 Problems with Upgrading 133 Glossary Public IP Address 134 135 Appendix a Specifications 136 137 Retreiving Client Certificate Next Select User Certificate, then Next 138 139 140 Enabling 802.1x Authentication and SecurityConnections 141 142 143 Enabling WPA Authentication and Security 144 145 Enabling WPA-PSK Authentication and Security 146