System Requirement and Installation | Dynalink RTA1025W specs

Chapter 2: System Requirement and Installation

7.Under the General tab, select Obtain an IP address automatically, and Obtain DNS server address automatically. Then click Ok to exit.

45

Image 58

Dynalink RTA1025W user manual System Requirement and Installation

Contents

ADSL2+ Wireless Modem Router User’s Manual Copyright Notice For Using For InstallationFor Service FCC Contents Web Configuration VII Viii Adsl Compliance FeaturesUnpacking ADSL2 Compliance ATM Features Wireless LAN ComplianceBridging Features Security Features Routing FeaturesConfiguration and Management Subscription for Adsl Service Physical Outlook LED IndicatorsFront Panel Rear Panel System Requirement Choosing a place for the Adsl Router Connecting the Adsl Router For Windows ME USB Driver InstallationFor Windows Page For Windows XP Page Right-click on My Computer and press Properties For Windows Vista System Requirement and Installation Page System Requirement and Installation Page System Requirement and Installation On the Control Panel folder, click System and Maintenance Click Device Manager System Requirement and Installation Method One Uninstalling the USB DriverMethod Two System Requirement and Installation Method Two System Requirement and Installation Unplug your USB cable between your router and your PC System Requirement and Installation Click System and Maintenance Press System Page Method Two uninstall from program list Page Setting up TCP/IP Page System Requirement and Installation Highlight Protocol and click Add System Requirement and Installation For Windows NT Highlight TCP/IP Protocol and click OK Enable Obtain an IP address from a Dhcp server and click OK For Windows Page Click Internet Protocol TCP/IP and then click OK Obtain an IP address automatically. Then click OK Connection Click Internet ProtocolTCP/IP and then click OK When it returns to the General Tab on the Local Area Click Network Internet Select Network and Sharing Center Click Manage Network Connection on the left side System Requirement and Installation Renewing IP Address on Client PC For Windows 98/ME For Windows NT/2000/XP Released IP Address For Windows Vista Page Accessing the Internet Description PPP over ATM PPPoA ModeConfiguration Primary IP address Subnet Mask Go to Advanced Internet Connections. And click Add PPP over ATM PPPoA IP Extension ModeVCI PPP over Ethernet PPPoE Mode PPP over Ethernet PPPoE IP Extension Mode ISP Numbered IP over ATM IPoA Primary IP Address IP Address Preferred DNS server Numbered IP over ATM IPoA+NAT Start IP Address End IP Address Unnumbered IP over ATM IPoA Check Dhcp Server Off and click Next IP Address Unnumbered IP over ATM IPoA+NAT Primary DNS server Secondary DNS server Subnet mask 255.255.255.248 Click Next Bridge Mode Primary IP address192.168.1.1 Start IP Address192.168.1.2 End IP AddressPage Web Configuration Using Web-Based Manager Language To Have the New Settings Take EffectOutline of Web Manager Title Main Menu Window Current Version Connect to Internet Quick SetupQuick Start Auto Scan Internet Connection PVC Connection Type PPP over ATM/ PPP over Ethernet Secondary IP Address & Subnet Mask Dial on DemandManually Connect Dhcp Server OnPage None Use the following DNS server addresses Dhcp Server On Bridging Page Status Overview Adsl Line Adsl BER Test Traffic Statistics Wireless ClientsInternet Connection Dhcp Table Host Name Advanced SetupLocal Network IP Address Domain Name Relay On Local Network Dhcp ServerServer and Relay Off Local Network UPnP Local Network Igmp Snooping Web Configuration Internet Connections Adding a New One 802.1Q Vlan Tagging Vlan ID Add Default Route Internet Igmp Proxy Igmp Proxy EnabledInternet DNS Server Internet Connection Bitswap Enable Adsl PortInternet Adsl Seamless Rate Adaptation Gateway IP Address IP Routing Static RouteNetmask WAN Interface RIP Version EnabledIP Routing Dynamic Routing Operation Virtual Server Port Forwarding IP Address seen by Internet Users Pre-defined User defined Virtual Server Port Triggering Virtual Server DMZ Host Virtual Server Dynamic DNS Virtual Server Static DNS IP Address： Enable VPN ALG NAT ALG ConfigurationEnable SIP ALG Firewall Firewall Bridge Filtering Firewall IP Filtering Select the direction to filter packets Source/Destination IP address Allow TrafficProtocol Port Range 100 Second generation Differentiated services code point Quality of ServiceFirst generation Precedence and type of service bits 101 Traffic Class Name Quality of Service Bridge QoS102 802.1p Priority 103 Quality of Service IP QoSWAN 802.1p 104 Group Name Port Mapping105 Available Interfaces 106 Basic Settings Wireless107 108 Security Select Wireless NetworkWireless Security 109 Format Authentication Type110 Key 1 to 111 For 802.1X Wireless Network802.1x environment Configuration Radius Shared Secret For WPA Wi-Fi Protected Access 112 For WPA-PSK WPA2-PSK Mixed WPA2/WPA-PSK 113Pre-Share Key For WPA-2 Mixed WPA2/WPA WPA2 Pre-authentication114 Network Re-auth Interval View Access Control List Access ControlAccess Control MAC Address of Wireless adaptor 116 AP ModeRepeater Search Other Repeaters Management DiagnosticsPress Run Diagnostic Tests on 117 Management Control From Remote Management Accounts118 Management Control From Local TR-069 Client Configuration119 120 Identify the Validation of Certificate from ACS 121 Internet Time 122 123 Configuring System LogSystem Log Log Level 124 System Log ConfigurationMode 125 Viewing System Log Remote Side Server 126 Viewing System Log Local Side Adsl Router Backup Config 127 Restore Update FirmwareReset Router 128 UPnP for XP 129 130 PC on the LAN cannot access the Web page of the Adsl Router Problems with LANProblems with WAN 131 Problems with Upgrading 132 Glossary 133 134 Public IP Address Appendix a Specifications 135 136 Retreiving Client Certificate 137 138 Next Select User Certificate, then Next 139 140 Enabling 802.1x Authentication and SecurityConnections 141 142 Enabling WPA Authentication and Security 143 144 Enabling WPA-PSK Authentication and Security 145 146