Manuals
/
Brands
/
Computer Equipment
/
Network Card
/
Eaton Electrical
/
Computer Equipment
/
Network Card
Eaton Electrical
34003991EN/EB
7.2.2.2 RS485 link configuration for 2 wires connexion
1
82
118
118
Download
118 pages, 2.84 Mb
Network Management Card
– User Manual
34003991EN/EB
Page
82/118
7.2.2.2
RS485 link configuration for 2 wires connexion
Set the SA2 switches like below to set the RS485 mode:
Set the SA1 switches to select the two wires configuration with no termination:
Contents
Main
Contents
Page
Page
1 EATON Network Solution
1.1 General Presentation
1.1.1 Connecting the UPS to the Ethernet network
1.1.2 Protection of the computers/servers
1.1.3 Supervision of the UPSs over the network
1.1.4 Connection
1.1.4.1 How to connect UPS / agent / network:
1.1.4.2 Setting up the protection:
1.2 Prese ntation of the Network Management Card (NMC) 1.2.1 Compatibility with UPSs
1.2.2 Direct sending of E-mail
1.2.3 Sending text messages (SMS)
1.2.4 Compatibility with the Network Management Systems (NMS) Trap sending
1.2.5 Environment Sensor (option)
1.3 Technical data 1.3.1 Hardware characteristics
1.3.2 EMC Compatibility
1.3.3 Configuration
1.3.4 Administration
1.3.5 Network
1.3.5.1 List of ports used
1.3.6 Environment sensor
1.3.7 MIB (Management Information Base)
1.3.8 Default parameters
2 Installation
2.1 Unpacking and check on contents
2.2 Indications
2.3 Installation in the UPS
2.4 Sensor installation (option)
3 Configuration
3.1 Configure IP parameters
3.1.1 Your network is equipped with a DHCP server
3.1.2 Your network is not equipped with a DHCP server
3.2 Test after configuration
4 Supervision and administration by browser
4.1 Optimising the performance of your browser
4.2 UPS 4.2.1 UPS properties page
4.2.1.1 "UPS" zone: general information on the UPS.
Page
Page
Page
Page
4.2.1.2 "UPS status" zone: Essential information
4.2.1.3 Viewing the modules
Page
4.2.1.4 Viewing the alarms
Page
4.2.1.5 Viewing the About your UPS window
4.2.2 On-line help
4.2.3 UPS control
Page
Page
4.2.4 UPS weekly schedule programming
4.2.5 Shutdown parameters
Page
4.2.6 Measurements
4.2.7 Event log
.
4.2.8 System log
4.3 Notification 4.3.1 Email Notification
Page
4.3.2 E-mail Message Settings
Page
4.4 Configuration
4.4.1 Network settings
Page
4.4.2 System
Page
4.4.3 Notified Applications
Page
4.4.4 Central shutdown configuration
4.4.5 Access control
Page
4.4.6 Date and time
.
Page
4.4.7 Firmware upload
4.5 Environment Sensor (option)
4.5.1 Characteristics
4.5.2 Environment Status
4.5.3 Environment Settings
Page
4.5.4 Log
5 Server protection
5.1 Set-up of the shutdown parameters
5.1.1 Shutdown criteria managed by the Network Management Card
Page
5.1.1.3 Shutdown when backup time is less than
5.1.1.4 Shutdown duration
5.1.2 Controlled outlets
5.1.3 Protection of a server connected to a controlled outlet
5.1.3.1 Load shedding or sequential shutdown
5.1.3.2 Sequential startup
5.2.2 Extended power outage, shutdown initiated by the "Low battery power" message
5.2.3 Case of power restoration before the end of the "shutdown duration" counter
5.3 Shutdown management with 2 NMC boards
5.3.1 Shutdown Duration
5.3.2 Settings
6 Configuration via RS232
6.1 Choice 1: Restart / Reset
6.2 Choice 2: Network Configuration
6.2.1 Choice 1: Read Network settings
6.2.2 Choice 2: Modify Network settings
6.2.3 Choice 3: Set Ethernet speed
6.3 Choice 3: Lost password / Set Login Password to Default
6.4 Choice 4: Return to Default Configuration
7 Industrial Network Management Card (INMC option)
7.1 Presentation 7.1.1 Overview
7.1.2 Functions
7.1.3 Technical characteristics
7.2 Installation 7.2.1 RS232 link configuration and connection
7.2.2 RS485 link configuration and connection
7.2.2.1 RS485 connection
Page
7.2.2.2 RS485 link configuration for 2 wires connexion
Page
7.2.2.3 RS485 link configuration for 4 wires connexion
Page
7.2.3 Configuration of the JBUS/MODBUS communication parameters
7.2.3.1 Choice 1: Display Jbus settings
7.2.3.2 Choice 2: Modify Jbus settings
7.2.3.3 Choice 3: Display Jbus diagnostics
7.2.3.4 Choice 4: Reset Jbus diagnostics
7.2.3.5 Choice 5: Return to Jbus Default Configuration
7.2.3.6 Choice 6: Display Jbus frames
7.3 Additional Web pages
7.4 JBUS table 7.4.1 Data for Pulsar 700 / 1000 / 1500
7.4.1.1 Status table
7.4.1.2 Measurements table
7.4.2 Data for Pulsar M 2200 / 3000
7.4.2.1 Status table
7.4.2.2 Measurements table
7.4.3 Data for Pulsar MX 4000 / 5000 / 10000 and EX 5 / 7 / 11 RT
7.4.3.1 Status table
7.4.3.2 Measurements table
7.4.4 Data for Pulsar MX frame 15 / 20
7.4.4.1 Status table
7.4.4.2 Modular fault table
Page
7.4.4.3 Measurements table
Page
7.4.5 Sensor data
7.4.5.1 Status table
7.4.5.2 Measurements table
7.4.5.3 Read of the personalization table
7.4.6 Other data
8 Appendices
8.1 Tables of alarms and events 8.1.1 Table of alarms
Page
Page
8.1.2 Table of UPS events
Page
8.1.3 Table of system alarms
8.2 SNMP objects 8.2.1 MGE MIB
Page
Page
8.2.2 Table des TRAPS : (1.3.6.1.4.1.705.1.11)
Page
9 Glossary
