49/118 | Eaton Electrical 34003991EN/EB guide

If the hostname is not used, the IP address supplied by the DHCP server must be fixed to maintain connection with the clients installed on the stations to be protected.

Note 2:

During the first connection, if the DHCP query is not successful, the NMC starts with the following IP configuration: IP address:166.99.16.16

Subnet mask: 255.255.255.0

Gateway Address: 0.0.0.0

◗Firmware Upload: Authorise (chose "Enabled") remote updating of the card's embedded software. The default value for this parameter is "Enabled".

◗Primary DNS Server: contains the IP address of the main DNS server ensuring conversion of the domain name to IP address.

◗Secondary DNS Server: contains the IP address of the secondary DNS server ensuring conversion of the domain name to IP address if the primary DNS server is not available.

◗SMTP Server: contains the name or IP address of the local server with which the card connects to send e-mails. It may be filled in either as host + domain name (DNS resolution), or directly with the IP address.

The default value is smtpserver. The card uses the standard port (25) for sending e-mails.

Important note:

The card must be rebooted after any changes to these parameters.. See "System" page

Security: The administrator has to click on Save and enter his/her login/password to save any modifications.

Network Management Card – User Manual

34003991EN/EB

Page 49/118

Image 49

Eaton Electrical 34003991EN/EB user manual 49/118

Contents

Network Management Card Contents Server Protection Configuration VIA RS232Industrial Network Management Card Inmc Option Appendices Jbus TableMGE MIB Glossary General Presentation Eaton Network Solution Protection of the computers/servers Connecting the UPS to the Ethernet network Connection Supervision of the UPSs over the network Setting up the protection How to connect UPS / agent / networkPresentation of the Network Management Card NMC Compatibility with UPSs Sending text messages SMS Direct sending of E-mailEnvironment Sensor option Hardware characteristics Technical dataConfiguration EMC Compatibility Network AdministrationEnvironment sensor List of ports used MIB Management Information Base BOOTP/DHCP Default parameters Unpacking and check on contents InstallationIndications LED Installation in the UPSACT Sensor installation option Configure IP parameters ConfigurationEaton Network Management Card Your network is equipped with a Dhcp server Your network is not equipped with a Dhcp server Test after configuration Optimising the performance of your browser Supervision and administration by browser UPS properties UPS UPS zone general information on the UPS 23/118 24/118 25/118 26/118 UPS status zone Essential information Viewing the modules 29/118 Viewing the alarms Alarm table for modular UPS Viewing the About your UPS window On-line help UPS control 35/118 36/118 UPS weekly schedule programming Shutdown parameters For the main outlet Master by default Measurements Event log System log Email Notification Notification 44/118 Mail Message Settings 46/118 Configuration Network settings 49/118 System 51/118 Notified Applications 53/118 Central shutdown configuration 55/118 Access control TLS Date and time 58/118 Firmware upload Environment Sensor option Characteristics Environment Status Environment Settings Display in the list of current alarms 4 Log Set-up of the shutdown parameters Server protectionShutdown criteria managed by the Network Management Card Utility failure Start of the shutdown sequence Shutdown duration Shutdown when backup time is less than Protection of a server connected to a controlled outlet Controlled outletsLoad shedding or sequential shutdown Sequential startup Different server and UPS shutdown sequences 70/118 Shutdown management with 2 NMC boards SettingsShutdown Duration Configuration via RS232 Choice 2 Network Configuration Choice 1 Restart / ResetChoice 1 Read Network settings Choice 3 Set Ethernet speed Choice 2 Modify Network settings Choice 3 Lost password / Set Login Password to Default Choice 4 Return to Default Configuration Presentation Industrial Network Management Card Inmc optionOverview Functions JBUS/MODBUS Technical characteristics 1 RS232 link configuration and connection Installation 2.1 RS485 connection 2 RS485 link configuration and connection 81/118 2.2 RS485 link configuration for 2 wires connexion 83/118 2.3 RS485 link configuration for 4 wires connexion 85/118 Configuration of the JBUS/MODBUS communication parameters Choice 2 Modify Jbus settings Choice 1 Display Jbus settings Choice 4 Reset Jbus diagnostics Choice 3 Display Jbus diagnosticsChoice 5 Return to Jbus Default Configuration Choice 6 Display Jbus frames Additional Web pages Data for Pulsar 700 / 1000 Jbus tableStatus table Measurements table Data for Pulsar M 2200 94/118 Data for Pulsar MX 4000 / 5000 / 10000 and EX 5 / 7 / 11 RT 96/118 Data for Pulsar MX frame 15 Modular fault table 99/118 100/118 101/118 5.1 Status table Sensor data 103/118 Read of the personalization table Other data Table of alarms Tables of alarms and eventsAppendices UPS OK If the UPS is modular UPS, for each module Table of UPS events 110/118 Table of system alarms MGE MIB Snmp objects 113/118 1yes 2no 1,4,1 MIB Trap Table des Traps 116/118 MIB Management Information Base GlossaryNetwork Management Proxy NSM Network Shutdown Module NMS Network Management Station SnmpSnmp Simple Network Management Protocol Smtp Simple Mail Transfer Protocol