Instruction Manual

760007-A July 2003

Model NGA2000 PMD

2-5 ELECTRICAL CONNECTIONS

NOTE

Electrical connections must be in compliance with National Electrical Code (ANSI/NFPA 70) and/or any applicable national or electrical codes.

Two electrical connections are required on the Analyzer Module; POWER and NETWORK.

See Figure 2-2 on page 2-4. On the Analyzer Module, two NETWORK connections are available, either of which is appropriate for : 1) interconnection with Backplane of the Platform (see Platform instruction manual) or 2) "daisy chaining" with other NGA2000 compo- nents.

Connect Analyzer Module POWER 24 VDC power source, either the Platform or external power source.

PRESSURE

COMPENSATION

BOARD

J5

J17

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

J6

J4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

J1

 

 

 

 

 

 

 

J9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

J10

 

 

J11

 

 

 

 

 

 

COMPUTER ANALYSIS

 

 

 

 

 

 

 

 

MAIN BOARD

 

 

 

 

 

J13

 

 

 

 

 

 

 

 

BOARD

 

 

J2

 

 

 

 

 

J12

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

J7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

J14

 

 

 

 

 

 

 

 

 

 

J3

 

 

 

 

 

 

 

J15

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

J19

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

J21

J22

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

W1

 

 

 

 

J16

J20

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PREAMP CABLE ASSEMBLY

FLOW SENSOR CABLE

CASE TEMP SENSOR

FAN

FLOW

SENSOR

SENSOR ASSEMBLY

MAGNET HEATER AND THERMAL CUTOFF

LED SOURCE ASSEMBLY

OPTICAL BENCH

Figure 2-5. PMD Wiring Diagram

2-6 Installation

Rosemount Analytical Inc. A Division of Emerson Process Management