Connecting to a VT Series Terminal | Enterasys Networks 9033989-06

Connecting to COM Port for Local Management

4.Turn on the PC and configure your VT emulation package with the following parameters:

Parameter	Setting

Mode	7	Bit Control

Transmit	Transmit=9600

Bits Parity	8	Bits, No Parity

Stop Bit	1	Stop Bit

5.When these parameters are set, the Local Management password screen will display. Refer to the appropriate Enterasys Matrix DFE‐Gold Series Configuration Guide for further information.

Figure 3-9 Connecting an IBM PC or Compatible

FAST ENET

4H4285-49

1

OFFLINE/

RESET

COM

MGMT CPU POE

GROUP

SELECT

GROUP

1 1

2 2

3 3

					Á
	Ã	Â	À
1	UTP straight-through cable with RJ45 connectors			3	RJ45-to-DB9 PC adapter
2	RJ45 COM port			4	IBM PC or compatible device

Connecting to a VT Series Terminal

To connect a VT Series terminal to an Enterasys Networks DFE module COM port

(Figure 3‐10), use a UTP straight‐through cable with RJ45 connectors and an RJ45‐to‐DB25 female adapter, and proceed as follows:

Matrix DFE-Gold Series PoE Module 4H4285-49 Installation Guide 3-19

Image 47

Enterasys Networks 9033989-06, 6H308-48, 4H4285-49 manual Connecting to a VT Series Terminal, Parameter Setting

Contents

Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Safety Information Class 1 Laser Transceivers Enterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Appendix C About PoE Power over Ethernet TroubleshootingAppendix a Specifications Appendix B Mode Switch Settings and Option Installations Tables Figures Xiv Important Notice About This GuideWho Should Use This Guide For Refer to How to Use This GuideRelated Documents Following conventions are used in this guide Conventions Used in This Guide Getting Help For information about Refer to Introduction 4H4285-49 Overview of DFE-Gold PoE Module CapabilitiesDFE-Gold Module DFE-Gold Module 4H4285-49 DFE-Gold Module Management Switch Configuration Using WebViewSwitch Configuration Using CLI Commands Connectivity Standards Compatibility Lanview Diagnostic LEDs Link Aggregation Network Requirements 100BASE-TX Network 10BASE-T Network Installation Unpacking the DFE Module Installation Site RequirementContents of DFE Module Carton Quantity DFE Module Placement and Installation Rules Installing Optional Network Expansion Module NEM Example 1 -1, a Example 3 -1, C Preparing to Install the 4H4285-49 Installing 4H4285-49 into a Matrix E7 or N7 Chassis Preparing to Install the 4H4285-49 Card guides Installing 4H4285-49 into Matrix N3 or N5 Chassis Card guides Connecting 48 Vdc Power for PoE Operation Making the UTP Connections Connecting to the NetworkConnecting UTP Cables to 4H4285-49 Connecting a Twisted Pair Segment with RJ45 Connector RX+ TX+ RX+ Verifying PoE Port Status Connecting to an IBM PC or Compatible Device Connecting to COM Port for Local ManagementWhat Is Needed Parameter Setting Connecting to a VT Series Terminal 10 Connecting a VT Series Terminal Connecting to a Modem 11 Connecting Using a Modem RJ45 DB25 Adapter Wiring and Signal AssignmentsCOM Port Adapter Wiring and Signal Diagram RJ45 VT Series Port Adapter Wiring and Signal Diagram Modem Port Adapter Wiring and Signal Diagram RJ45 DB25 Completing the InstallationCompleting the Installation of a New System First-Time Log-In Using a Console Port Connection 12 Matrix Defogged Startup Screen Example N7 Chassis Enter Logging in with an Administratively-Configured User Account Completing the Installation About the Management Mgmt LED TroubleshootingUsing Lanview Lanview LEDs Viewing Receive/Transmit Activity Color State Recommended Action Viewing the PoE Port Status Alternately 67% on, 33% LED RX/TX Refer to the Matrix DFE-Gold Series Configuration Troubleshooting Checklist Matrix DFE-Gold Series Configuration Guide for OFFLINE/RESET Switch Overview of DFE Module Shutdown Procedure Last Resort Shutdown Procedure Using OFFLINE/RESET Switch Recommended Shutdown Procedure Using OFFLINE/RESET Switch Table A-1 4H4285-49 Specifications Specifications4H4285-49 Specifications Processors/Memory Table A-1 4H4285-49 Specifications ItemSpecification Table A-3 Compliance Standards Regulatory Compliance Table A-2 COM Port Pin Assignments Signal Name Input/OutputCOM Port Pinout Assignments Regulatory Compliance Regulatory Compliance Specifications Required Tools Mode Switch Settings and Option Installations Setting the Mode Switches Memory Locations and Replacement Procedures Memory Locations and Replacement Procedures Gaining Access to Memory Modules Gaining Access to Memory Modules Removing the Safety Cover Figure B-3 Removing the Safety Cover Removing the Network Expansion Module NEM Dram Simm Replacement Procedure Figure B-5 Removing the Existing Dram Simm Removing the Dram Simm Figure B-6 Installing the Dram Simm Installing the Dram Simm Removing the Dimm Dimm Replacement Procedure Figure B-8 Installing the Dimm Installing the Dimm Figure B-9 Installing the Network Expansion Module Reinstalling the Optional Network Expansion Module Reinstalling the Safety Cover Figure B-10 Installing the Safety Cover Overview About PoE Power over Ethernet Front Panel 48 Vdc Interface Power InterfaceProprietary PD Detection Matrix N5 Backplane 48 Vdc Interface Table C-2 PoE Status LED Indications PoE Port Status PoE Port Status LEDs PoE Port Status LEDs About PoE Power over Ethernet Numerics Index Pinout assignments console port A-3