Connecting a VT Series Terminal | Enterasys Networks 6H308-48

Connecting to COM Port for Local Management

1.Connect the RJ45 connector at one end of the UTP straight‐through cable to the COM port on the Enterasys Networks module.

2.Plug the RJ45 connector at the other end of the UTP straight‐through cable into the RJ45‐to‐DB25 female adapter.

3.Connect the RJ45‐to‐DB25 adapter to the port labeled COMM on the VT terminal.

4.Turn on the terminal and access the Setup Directory. Set the following parameters on your terminal:

Parameter	Setting

Mode	7	Bit Control

Transmit	Transmit=9600

Bits Parity	8	Bits, No Parity

Stop Bit	1	Stop Bit

When these parameters are set, the Local Management password screen will display. Refer to the Enterasys Matrix DFE‐Gold Series Configuration Guide for further information.

Figure 3-10 Connecting a VT Series Terminal

FAST ENET

4H4285-49

1

OFFLINE/

RESET

COM

MGMT CPU POE

GROUP

SELECT

GROUP

1 1

2 2

3 3

Á

			Â

	Ã			À
1	UTP straight-through cable with RJ45 connectors					3	RJ45-to-DB25 VT adapter
2	RJ45 COM port					4	VT series terminal

3-20 Installation

Image 48

Enterasys Networks 6H308-48, 4H4285-49, 9033989-06 manual Connecting a VT Series Terminal

Contents

Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Safety Information Class 1 Laser Transceivers Enterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Troubleshooting Appendix a SpecificationsAppendix B Mode Switch Settings and Option Installations Appendix C About PoE Power over Ethernet Figures Tables Xiv About This Guide Who Should Use This GuideImportant Notice How to Use This Guide Related DocumentsFor Refer to Conventions Used in This Guide Following conventions are used in this guide Getting Help Introduction For information about Refer to Overview of DFE-Gold PoE Module Capabilities DFE-Gold Module4H4285-49 DFE-Gold Module 4H4285-49 DFE-Gold Module Switch Configuration Using WebView Switch Configuration Using CLI CommandsConnectivity Management Lanview Diagnostic LEDs Standards Compatibility Network Requirements Link Aggregation 10BASE-T Network 100BASE-TX Network Installation Installation Site Requirement Contents of DFE Module Carton QuantityUnpacking the DFE Module Installing Optional Network Expansion Module NEM DFE Module Placement and Installation Rules Example 1 -1, a Example 3 -1, C Preparing to Install the 4H4285-49 Installing 4H4285-49 into a Matrix E7 or N7 Chassis Preparing to Install the 4H4285-49 Card guides Installing 4H4285-49 into Matrix N3 or N5 Chassis Card guides Connecting 48 Vdc Power for PoE Operation Connecting to the Network Connecting UTP Cables to 4H4285-49Making the UTP Connections Connecting a Twisted Pair Segment with RJ45 Connector RX+ TX+ RX+ Verifying PoE Port Status Connecting to COM Port for Local Management What Is NeededConnecting to an IBM PC or Compatible Device Connecting to a VT Series Terminal Parameter Setting 10 Connecting a VT Series Terminal Connecting to a Modem 11 Connecting Using a Modem Adapter Wiring and Signal Assignments COM Port Adapter Wiring and Signal Diagram RJ45VT Series Port Adapter Wiring and Signal Diagram RJ45 DB25 Completing the Installation Completing the Installation of a New SystemModem Port Adapter Wiring and Signal Diagram RJ45 DB25 First-Time Log-In Using a Console Port Connection 12 Matrix Defogged Startup Screen Example N7 Chassis Logging in with an Administratively-Configured User Account Enter Completing the Installation Troubleshooting Using LanviewAbout the Management Mgmt LED Viewing Receive/Transmit Activity Lanview LEDs Viewing the PoE Port Status Color State Recommended Action Alternately 67% on, 33% LED RX/TX Troubleshooting Checklist Refer to the Matrix DFE-Gold Series Configuration Matrix DFE-Gold Series Configuration Guide for Overview of DFE Module Shutdown Procedure OFFLINE/RESET Switch Recommended Shutdown Procedure Using OFFLINE/RESET Switch Last Resort Shutdown Procedure Using OFFLINE/RESET Switch Specifications 4H4285-49 SpecificationsTable A-1 4H4285-49 Specifications Table A-1 4H4285-49 Specifications ItemSpecification Processors/Memory Table A-2 COM Port Pin Assignments Signal Name Input/Output COM Port Pinout AssignmentsRegulatory Compliance Table A-3 Compliance Standards Regulatory Compliance Regulatory Compliance Specifications Mode Switch Settings and Option Installations Required Tools Setting the Mode Switches Memory Locations and Replacement Procedures Memory Locations and Replacement Procedures Gaining Access to Memory Modules Gaining Access to Memory Modules Removing the Safety Cover Figure B-3 Removing the Safety Cover Dram Simm Replacement Procedure Removing the Network Expansion Module NEM Removing the Dram Simm Figure B-5 Removing the Existing Dram Simm Installing the Dram Simm Figure B-6 Installing the Dram Simm Dimm Replacement Procedure Removing the Dimm Installing the Dimm Figure B-8 Installing the Dimm Reinstalling the Optional Network Expansion Module Figure B-9 Installing the Network Expansion Module Reinstalling the Safety Cover Figure B-10 Installing the Safety Cover About PoE Power over Ethernet Overview Power Interface Proprietary PD DetectionMatrix N5 Backplane 48 Vdc Interface Front Panel 48 Vdc Interface PoE Port Status LEDs Table C-2 PoE Status LED Indications PoE Port Status PoE Port Status LEDs About PoE Power over Ethernet Index Numerics Pinout assignments console port A-3