ANG-3000/7000, Aurorean Network | Enterasys Networks ANG-1100

Connecting Cables	Chapter 2
	Installation

Connecting an ANG-1102/1105

The ANG-1100 is typically set up in the configuration shown below.

INTERNET

Site-to-site tunnel

ANG-3000/7000

Users

External (WAN)

Trusted (LAN)

Cable /

DSL

connection

connection

Modem

or

Hub

Aurorean Network

Gateway-1100

Site-to-site tunnel

User

Internet connection

User

Trusted connection

Figure 6 Connecting the ANG-1100

To connect the ANG-1100 Ethernet port, perform the following steps:

1Do one of the following as shown in Figure 7:

–If you are connecting an ANG-1102 to a hub, plug one end of a straight-through Ethernet cable into the ANG’s trusted port. If you are connecting an ANG-1105 to a PC, plug one end of a straight-through cable into the ANG’s trusted port. If you are connecting an ANG-1105 to a hub, plug one end of the red, cross- over cable to a trusted port. Go to Step 2.

–If you are connecting the ANG-1102 directly to a computer, attach one end of the red, cross-over cable to a trusted port and the other end to an RJ45 connector on your computer. Skip to Step 3.

2Plug the opposite end of the cable into a wall jack, patch panel, or hub linked to a protected network segment.

6	Aurorean Network Gateway-1100 User’s Guide

Image 18

Enterasys Networks ANG-1100 manual Do one of the following as shown in Figure, ANG-3000/7000, Aurorean Network

Contents

ANG-1100 User’s Guide Aurorean Virtual Network Aurorean Network Gateway-1100 User’s Guide Iii Important Safety Instructions Table of Contents Configuring the ANG-1100 with Aurorean Web Table of Contents United States Government Restricted Rights Page Contents of the Guide About This Guide Conventions Used in This Guide Related Publications About This Guide Related PublicationsPage Overview System Description ANG-1102/1105 Topology System Description Installation Unpacking the ANG-1102/1105 Accessories Location PlanningUnpacking the ANG-1102/1105 Chapter Connecting Cables Connecting CablesEthernet Connections Do one of the following as shown in Figure ANG-3000/7000Aurorean Network Reset TER NAL Serial Connection Connecting Power to the ANG-1102/1105 Connecting Power to the ANG-1102/1105 Chapter Connecting the Power Cable to the Power Supply Connecting Power to the ANG-1102/1105 Checking ANG-1102/1105 Connections LED behaviorChecking ANG-1102/1105 Connections Chapter Configuring the ANG-1100 with Aurorean Web Config Before You Begin Configuring the ANG-1100 with Aurorean Web Config Login window appears as shown in Figure Logging into Web ConfigTo log into Web Config, perform the steps below VPN Status window appears as shown in Figure Set Password window appears as shown in Figure Setting Your PasswordClick the Set Password menu option Set Password Viewing VPN Status VPN Status Setting Up the VPN Click the VPN Setup menu optionVPN Setup window appears as shown in Figure Aurorean Network Gateway VPN Setup Assigned VPN Connections Select one of the following Connection modes Click Apply Setting Up the Internet Connection Click the Internet Setup menu optionInternet Setup window appears as shown in Figure Internet Setup Window Do one of the following Internet Setup Configuring the ANG-1100 with Aurorean Web Config Firmware Update window appears as shown in Figure Click the Firmware Upgrade menu optionFirmware Upgrade window appears as shown in Figure Firmware Update Second Firmware Update Window Aurorean Network Gateway Firmware Update Image Date and Build Information LAN Setup window appears as shown in Figure Setting Up the LANClick the LAN Setup menu option LAN Setup Configuring the ANG-1100 with Aurorean Web Config Setting Up the Firewall Firewall Setup window appears as shown in Figure Begin Firewall Setup by performing the following stepsClick the Firewall Setup menu option Firewall Setup Setting Your Password Set Password Window Checking Device Status Click the Device Status menu optionDevice Status window appears as shown in Figure Device Status Window Interrupts Network DevicesRoute Table System Log Using Advanced Utilities Advanced Utilities window appears as shown in FigureAdvanced Utilities Using the Configuration Editor Click the Configuration Edit menu option Configuration Edit window appears as shown in Figure Configuring the ANG-1100 with Aurorean Web Config Configuring IP Port Forwarding Follow the steps below to configure IP port forwarding Switch Arg DefinitionUsage Example Page Aurorean Network Gateway Aurorean Web ConfigGlossary Aurorean Policy Server Ethernet Firewall IP Address Internet Service Provider ISPGeneric Routing Encapsulation GRE IP Security Protocol IPSec Network Address Translation NAT Network Administrator LEDsMac Address Point-to-Point Tunneling Protocol Pptp Point of Presence POPPoint-to-Point Protocol PPP PPPoE Routers TunnelingVirtual Private Network VPN Specifications This appendix details the specifications of the ANG-1100Category Parameters Specifications Vcci Page Pin Assignments Pin Signal Ethernet Port Pin Assignments DB-9 Serial Port Pin AssignmentsPage Program License Agreement Support Enterasys Networks, Inc. Program License Agreement Applicable Law LicenseOther Restrictions Export Requirements Exclusion of Warranty United States Government Restricted RightsUnited States Government Restricted Rights No Liability for Consequential Damages Technical SupportSupport from Enterasys Networks Returning Products for Repair Technical SupportPage Index VPN LED Index LAN POP Index