User’s Guide

Problem Solving

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

117

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

: lit

 

 

: flashing

 

 

: off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Status

Cause

 

 

 

 

Remedy or Status

 

 

 

 

 

 

 

 

 

 

 

Red

Red

Lamp cover is open error/

Take out the lamp and check if it is broken. Replacing the Lamp

 

p.142

 

 

 

 

 

 

 

Lamp timer failure/

If the lamp is not broken, put it back in and then turn the power on. If the lamp still does not turn

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Lamp out

on, replace it with a new lamp.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If this does not solve the problem, stop using the projector and disconnect the power cable from

 

 

 

 

 

 

 

 

the electrical outlet. Then contact your dealer or the nearest address provided in the "International

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Warranty Conditions" section of the Safety Instructions/World-Wide Warranty Terms booklet.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If the lamp is broken.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Contact your local dealer for further advice.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(Projection cannot be carried out until the lamp is replaced.)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Check that the lamp and the lamp cover are securely installed. If the lamp or lamp cover is not

 

 

 

 

 

 

 

 

 

 

securely installed, the lamp will not switch on.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Red

 

Red

Internal temperature error

The lamp will turn off automatically and projection will stop. Wait for about 5 minutes without

 

 

 

(overheating)

operating the projector. After confirming that the projector enters Standby state, check the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

following two points. When done the checking, press the [Power] button to turn the power back

 

 

 

 

 

 

 

 

on.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

•Check that the air filter and air exhaust vent are clear, and that the projector is not positioned

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

against a wall.

p.16

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

•If the air filters are blocked, clean or replace them.

p.140

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If the projector continues to overheat even after the above points have been checked, or if the

 

 

 

 

 

 

 

 

 

 

indicators show a problem when the power is turned back on, stop using the projector, disconnect

 

 

 

 

 

 

 

 

the power cable from the electrical outlet, and contact your dealer or the nearest address provided

 

 

 

 

 

 

 

 

in the "International Warranty Conditions" section of the Safety Instructions/World-WideWarranty

 

 

 

 

 

 

 

 

Terms booklet.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Red

 

Orange

High-speed cooling in progress

(This is not an abnormality, However, if the temperature rises too high again, projection will stop

 

 

 

 

automatically.)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

•Check that the air filters and air exhaust vent are clear and that they are not up against a surface

 

 

 

 

 

 

 

 

such as a wall.

p.16

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

•If the air filter is blocked, clean it.

p.140

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Orange

Lamp replacement notification

Replace the lamp with a new one.

p.142

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If you continue to use the lamp after it has passed the replacement period, the possibility that the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

lamp may break will increase. Replace the lamp with a new one as soon as possible.

 

 

 

 

 

 

 

 

 

 

* The

 

indicator status will vary depending on the projector status at the time.