User’s Guide

 

Problem Solving

 

 

 

 

 

 

127

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The remote control does not work

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Check

 

 

 

Remedy

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Is the [R/C] switch at the "ON" position?

Set the [R/C] switch to the "ON" position.

p.36

 

 

 

 

 

 

 

 

 

 

 

 

 

Is the remote control light-emitting area

Face the remote control towards the remote control light-receiving area.

 

 

 

 

facing towards the remote control light-

The operating angle for the remote control is approximately ±30º horizontally and approximately

 

 

 

receiving area when it is operated?

±15º vertically.

p.14

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Is the remote control too far from the

The operating range for the remote control is approximately 10 m.

p.14

 

 

 

 

projector?

If operating the remote control from a distance or if you would like to ensure that remote control

 

 

 

 

 

operations work properly, use the optional remote control cable kit.

p.151

 

 

 

 

 

 

 

 

 

Is direct sunlight or strong light from

Set the projector up in a location where strong light will not shine onto the remote control light-

 

 

 

 

fluorescent lamps shining onto the remote

receiving area.

 

 

 

 

 

 

 

 

 

 

control light-receiving area?

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Are the batteries dead, or have the batteries

Insert new batteries, while making sure that they face correctly.

p.12

 

 

 

 

been inserted correctly?

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Does the remote control's ID number match

If the remote control's ID number is set to a number other than "0", the ID number must match the

 

 

 

 

the projector's ID number?

projector's ID number, otherwise the remote control will not work.

p.74

 

 

 

 

 

 

 

 

 

Is the remote control cable still connected to

If the remote control cable is still connected to the [Remote] port, the remote control light-receiving

 

 

 

 

the [Remote] port of either the remote control

areas of the projector or the remote control light-emitting area of the remote control will not work. If

 

 

 

or the projector?

not using the remote control cable kit, disconnect the remote control cable from the [Remote] port of

 

 

 

 

 

either the remote control or the projector.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The fans do not stop when power is turned off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Check

 

 

 

Remedy

 

 

 

 

 

 

 

 

 

 

 

 

 

Is the "Standby Mode" configuration menu set

If the menu is set to "Network ON", the fans will continue to operate after the cool-down period has

 

 

 

 

to "Network ON"?

finished.

 

 

 

 

 

 

 

 

 

 

 

 

"Advanced1" - "Standby Mode"

p.91